Miele G 673 Operating Instructions Manual Download Page 67 | Manualshive

Page: 67 / 84

background image

The weight of the door front will af-
fect the functioning of the door
springs. After fitting it is essential for
this to be checked out. See Step 6.

The door front is fixed to the machine
door outer panel using a fixing bracket.
This fixing bracket has to be pre-
mounted on the rear of the door front.

When the dishwasher is delivered the
fixing bracket is secured to the dish-
washer. To remove it:

Loosen the fixing screws (arrow) on
each side of the machine door outer
panel.

Push the fixing bracket upwards
from the sprung bolts and remove.

Remove the protective packaging.

Installation

67

«
...
65
66
67
68
69
...
»

Summary of Contents for G 673





















































































Reviews:

No comments

Related manuals for G 673

Brand: Jackson Pages: 48

Brand: Blomberg Pages: 43

Brand: Crosley Pages: 60

Brand: Indesit Pages: 84

Brand: NEFF Pages: 52

Brand: Jenn-Air Pages: 76

Brand: Parmco Pages: 36

Brand: Bush Pages: 48

Brand: Zanussi Electrolux Pages: 22

Brand: V-ZUG Pages: 52

Brand: Samsung Pages: 44

Brand: Electrolux Pages: 8

Brand: Electrolux Pages: 16

Brand: Electrolux Pages: 22

Brand: Electrolux Pages: 28

Brand: Electrolux Pages: 20

Brand: Electrolux Pages: 16

Brand: Electrolux Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands