Miele G 673 Operating Instructions Manual Download Page 22

Page: 22 / 84

Add rinse aid only until it is visible on
the surface of the filter in the open-
ing.

Close the flap firmly.
The flap must audibly engage, other-
wise water could get into the rinse
aid storage container during the pro-
gramme.

Mop up any spilt rinse aid. This pre-
vents over-foaming occuring during
the next programme.

The flap should normally remain
closed. Only open it for adding more
rinse aid.

Wait until the indicator light

on the

control panel lights up before adding
more rinse aid.

Setting the dosage

The dosage adjuster (see arrow) in the
opening has settings from 1 to 6. It is
set to 3 at the factory, as the recom-
mended dose. The setting dispenses
approx. 3 ml rinse aid per programme.

If there are flecks on glasses after
drying use a higher setting.

If smearing appears on crockery use
a lower setting.

Adding rinse aid

Summary of Contents for G 673





















































































Search results

Summary of Contents for G 673

Reviews:

Related manuals for G 673

Brands by name

Popular brands

Miele G 673, Operating Instructions Manual

Search results

Summary of Contents for G 673

Reviews:

Related manuals for G 673

Brands by name

Popular brands