Miele G 673 Operating Instructions Manual Download Page 17 | Manualshive

Page: 17 / 84

background image

Press touch pad

c

to be able to enter

data. The indicator light

c

goes out.

Indicator lights

b

,

e

and

f

also go

out if previously on, and the corre-
sponding water hardness level has
not been selected.

Press the touch pad corresponding
to the water hardness to be set (see
settings chart). While the selected
pad is pressed in its indicator light
stays on.
With a water hardness above 220 mg/l
(12 °d German scale) first press the

2

touch pad, (its

2

indicator will light

up) to access programming level 2.
Example: Where the water hardness
is 430 mg/l (25 °d German scale),
press

2

and then press touch pad

e

.

Release the touch pad, the indica-
tors

k

and

c

will flash.

Press touch pad

2

. Its indicator

lights up and the

k

indicator light

flashes.

Press the

2

touch pad again. The in-

dicators

2

and

k

will flash.

Switch off the dishwasher. The pro-
grammed water softener setting is
now programmed according to the
water hardness and is stored.

To check the programmed
water hardness:

Open the door.

Switch off the dishwasher.

Press and hold the touch pads

b

and

d

and at the same time switch on the

dishwasher.
The "On" indicator light comes on and
the

k

and

c

indicator lights flash.

Warning: If some other indicator light
flashes switch off the dishwasher and
start again.

The following indicator lights can come
on in addition to the "On" indicator light:

b

–

The drying heat is switched off
(see section on "Additional
functions").

e

–

The buzzer is switched off (see
section on "Additional functions").

f

–

Special function for the Service
Engineer only.

Press touch pad

c

to check the pro-

grammed water softener setting. The
indicator light

c

goes out. Indicator

lights

b

,

e

and

f

also go out if

these have been on previously and
the corresponding water hardness
level has not been selected.

If the water softener has been set for a
water hardness between 0 and
220 mg/l (0 °d and 12 °d German
scale) the indicator light in the rele-
vant touch pad lights up (see set-
tings chart).
If no indicator lights up the softener
has been set for a water hardness
between 230 and 1260 mg/l (13 °d
and 70 °d German scale. Then:

Press the

2

touch pad, to access

programming level 2, its indicator

2

lights up.
The indicator light of the touch pad
which corresponds to the water hard-
ness set lights up (see settings
chart).

Switch off the dishwasher.

Water softener

17

«
...
15
16
17
18
19
...
»

Summary of Contents for G 673





















































































Reviews:

No comments

Related manuals for G 673

Brand: Fagor Pages: 78

Brand: Fagor Pages: 20

Brand: Fagor Pages: 2

Brand: Fagor Pages: 1

Brand: VOX electronics Pages: 154

Brand: Kleenmaid Pages: 36

Brand: Hanseatic Pages: 72

Brand: INVENTOR Pages: 68

Brand: Indesit Pages: 16

Brand: Ariston Pages: 12

Brand: Smeg Pages: 44

Brand: Hotpoint Pages: 28

Brand: GE Pages: 48

Brand: Hotpoint Pages: 16

Brand: Hoonved Pages: 21

Speed Queen AWM190

Brand: Raytheon Pages: 86

Brand: Electrolux Pages: 30

Brand: Electrolux Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands