Miele G 673 Operating Instructions Manual Download Page 38 | Manualshive

Page: 38 / 84

background image

Switching on and off

Switching on

Open the door.

Open the stopcock (if it is closed).

Press the "I" (On) touch pad (20).
The "On" indicator light comes on.

Starting a programme

Press the touch pad for the required
programme.The indicator light
comes on in the touch pad pressed.

If required select "Top solo" (

2

) be-

fore starting the programme.
(see section "Additional options and
functions").

Close the door. The programme
starts.

For information

The "Reactivation" process is car-
ried out before a wash programme.
It lasts several minutes.

The hardness level of the inlet water
dictates how often (after how many pro-
grammes) water needs to be softened.
For example with a water hardness de-
gree of 380 mg/l (21 °d German scale)
reactivation takes place after every 3
programmes. With a water hardness de-
gree of 140 mg/l (8 °d German scale)
reactivation takes place after 8 pro-
grammes.

Do not cancel the programme pre-
maturely, as important programme
steps such as preparing the water
softener may be left out.

Programme end

A buzzer sounds at the end of the pro-
gramme cycle.

This buzzer is then repeated for one
hour at ten minute intervals.

You can switch this buzzer off (see sec-
tion on "Additional options and func-
tions").

Switching on and off

38

«
...
36
37
38
39
40
...
»

Summary of Contents for G 673





















































































Reviews:

No comments

Related manuals for G 673

Brand: Samsung Pages: 17

Brand: Fagor Pages: 28

Brand: Zanussi Pages: 28

Brand: Gorenje Pages: 38

Brand: Smeg Pages: 44

WAREFORCE UH 30

Brand: Jackson Pages: 57

Brand: NEFF Pages: 52

Brand: Bush Pages: 25

MF200D80WB Series

Brand: Midea Pages: 44

Brand: IKEA Pages: 68

Brand: Gaggenau Pages: 72

Brand: Russell Hobbs Pages: 28

Brand: Mach Pages: 45

Brand: AEG Pages: 32

Brand: AEG Pages: 60

Brand: AEG Pages: 28

Brand: AEG Pages: 60

Brand: Electrolux Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands