manualshive.com logo in svg

Miele FashionMaster, Operating Instructions Manual

Share
Download
Miele FashionMaster Operating Instructions Manual Download Page 73

Problem solving guide

73

Problem

Cause and remedy

Message in the display:

 

Boiler fault, cold Switch

off/on

There is a fault.

Press the 

 button to switch the steam ironing

system off and then back on again.

If the fault continues to be displayed, contact
Miele Service.

Message in the display:

 

Release stm. button

The iron has switched itself off because it has not
been used for a period of time and the steam button
 

 has locked.

Unlock the steam button 

 by pushing the slider

for continual steam on the iron forwards.

Message in the display:

 

Drainage fault Switch

off/on

The residual water drawer has not been detected.

Press the 

 button to switch the steam ironing

system off and then back on again.

After switching the steam ironing system off and back
on, the residual water drawer has not been detected.

Press the 

 button to switch the steam ironing

system off.

Clean and dry the metal discs (contacts) on the re-
sidual water drawer.

Use the 

 button to switch the steam ironing sys-

tem back on and follow the instructions shown in
the display:

Remove the residual water drawer and fill it with
fresh tap water.

Put the filled residual water drawer back in the
tower.

Remove the residual water drawer again when you
are prompted to do so and the appropriate mes-
sages are shown in the display.

Empty and dry the residual water drawer.

Put the empty residual water drawer back in the
tower.

The steam ironing system is now ready for operation
and will continue to operate from the point reached
before the fault was registered.

There is a fault.

If the fault message continues to be displayed,
contact Miele Service.

Summary of Contents for FashionMaster

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands