manualshive.com logo in svg

Miele FashionMaster, Operating Instructions Manual

Share
Download
Miele FashionMaster Operating Instructions Manual Download Page 29

Switching on

29

Filling the water container

If the water container is empty or not
installed in the tower, the message

 

Fill water cont.

 will appear in the dis-

play.

Removing the water container

Hold the water container by its
handle.

Pull the handle downwards.

The water container is released from the
retainer.

Pull the water container upwards and
out.

When removing the water container,
you may notice some water dripping
while the water container valves are
closing.

Tip: 

The dripping can be prevented by

removing the water container slowly.

Filling the water container

Open the screw cap at the rear of the
water container by turning the cap
anti-clockwise.

Remove the screw cap.

Use fresh tap water to fill the con-
tainer (water temperature approx.
15 - 35 °C).

Tip: 

By placing the water container in

the horizontal position, the water con-
tainer can also be filled under very low
taps.

Replace the screw cap on the water
container.

Close the screw cap by turning it
clockwise as far as it will go.

Put the water container back into the
tower.

The water container can be removed
and refilled at any time (even during
the ironing process). The amount of
water required will depend on how
much steam is required.

Summary of Contents for FashionMaster

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands