Microcom 334M Operator'S Manual Download Page 175 | Manualshive

Page: 175 / 237

background image

9-1

334M Operator’s Manual - 880060-0110

Chapter 9 Code Page Switching

9.1 What is Code Page Switching?

There are 256 numeric codes used on the PC to represent letters, symbols, and numbers.
Up to 256 codes are available to represent lower and upper case letters, numbers,
punctuation marks, and all the mathematical symbols on a PC’s keyboard.  This may seem
like more than enough, but it is not possible to represent all the letters and characters used
in every language using one character set of 256 codes.
For example:

§

Some languages have a much larger alphabet than others and include many

accented characters.

§

Many graphics characters are used.

9.2 Character Sets

To accommodate the use of different languages, the 334M printer provides a number of
character sets. The numeric codes sent by the PC to the printer represent different
characters depending on which character set is being used by the printer.

Code page 437 is the famous original IBM PC character set. It is the most common and is
used for several languages, including English, German, and French. Character sets 865
and 860 contain the characters needed for Danish and Portuguese, respectively. In these
character sets, some symbols available in 437 have been removed to make room for the
extra letters needed. For example, the code for (franc) has been used for Ó in 860.

These character sets are stored in the printer’s FLASH memory as tables called code
pages. The printer allows you to change the code page that is being used by changing the
settings in Soft Switch #4, using the ^D24 command.

9.3 Code Pages

The 334M printer provides 15 standard code pages. Please note that the printer
implements the codes from 32 up. Code numbers below 32 are printed using the 334M’s
standard letters. These are the Code Pages that are implemented in the printer:

1.  Code Page 437
2.  Code Page 850
3.  Code Page 852
4.  Code Page 860
5.  Code Page 863
6.  Code Page 865
7.  USA
8.  British
9.  German
10. French
11. Italian
12. Danish
13. Spanish
14. Swedish
15. Swiss

«
...
173
174
175
176
177
...
»

Summary of Contents for 334M














































































































































































































































Reviews:

No comments

Related manuals for 334M

Brand: Lanier Pages: 3

VariQuest Perfecta 2400STP

Brand: Varitronics Pages: 227

Brand: Xerox Pages: 4

Brand: Oki Pages: 62

Brand: TallyGenicom Pages: 144

Brand: Oki Pages: 1

imageRUNNER 5075

Brand: Canon Pages: 502

imageRUNNER 5075

Brand: Cannon Pages: 268

VersaCamm SP-300V

Brand: Roland Pages: 4

Brand: Oki Pages: 24

Brand: Ricoh Pages: 140

mobile pro advance

Brand: AM TECH Pages: 16

Brand: MHM Pages: 52

Brand: QMS Pages: 188

Brand: Sinfonia Technology Pages: 41

Brand: IBM Pages: 128

Brand: Felix Storch Pages: 35

Brand: AccuBANKER Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands