Metz Clarus Operating Instructions Manual Download Page 106

Page: 106 / 114

106

Problem

Possible cause

Remedy

TV set does not react
to commands from
the remote control

• No line of sight between the

remote control and the TV set.

• Sunlight is shining directly on

the infrared window of the TV
set.

• Batteries of the remote control

are exhausted.

• TV set has been switched off

with the main power switch.

• Fault in the internal processor.

• Remove any obstacles

between the units.

• Prevent sunlight from

shining on the set.

• Replace the batteries.
• Switch on the TV set

with the main power

switch.

• Switch off the TV set

with the main power

switch, wait a few

seconds and then switch

it on again.

The message "Enter
code" is displayed
when the TV set is
switched on.

• The childlock is active and was

programmed to disable all
stations.

• Enter the code you used

when programming the
childlock.

The TV set will not
switch to a selected
programme position.
A teddy bear is dis-
played instead.

• The childlock is active and was

programmed so that only the
stations shown in the list beside
the teddy bear may be selec-
ted.

• Enter the code you used

when programming the
childlock.

You have switched
off the TV set with
the

key, but the

green LED remains
on.

• EPG data are currently being

collected from the programmed
EPG station.

• None. When all data

have been collected, the
TV set will switch itself
off automatically.

Direct recording of an
analogue terrestrial
station (received via
roof antenna or
cable) with Data Logic
does not work.

• The Data Logic video recorder

is not connected to the roof
antenna or cable outlet with a
suitable cable.

• Connect the Data Logic

video recorder to the
roof antenna or cable
outlet with a suitable
cable.

607 47 2042.A1 Clarus GB 04.12.2007 9:59 Uhr Seite 106

Downloaded From TV-Manual.com Manuals

Summary of Contents for Clarus



















































































































Search results

Summary of Contents for Clarus

Reviews:

Related manuals for Clarus

Brands by name

Popular brands

Metz Clarus, Operating Instructions Manual

Search results

Summary of Contents for Clarus

Reviews:

Related manuals for Clarus

Brands by name

Popular brands