Mercury MerCruiser Axius SeaCore 350 MAG Manual Download

Page: 49 / 170

Section 2 - Getting to Know Your Power Package

90-8M0050539

eng

MAY 2011

Page 41

The power trim system is protected from overload by both a 110 amp fuse and a 20 amp spade fuse on the power trim pump. The

trim pump may also have an in‑line circuit protection device in the power trim positive lead near the battery switch or battery

connection.

a -

20 amp spade fuse

b -

110 amp fuse

A power harness, connected to the engine starting battery, minimizes voltage drop to the electrical system. This harness is

protected by a 5 amp fuse. This connection is located at the rear of the engine, near the 14‑pin connector.

33179

Power harness connection

The Quicksilver Three‑Button Power Trim Control Panel is protected by a 20 amp in‑line fuse.

mc70527-1

9208

Summary of Contents for MerCruiser Axius SeaCore 350 MAG











































































































































































Search results

Summary of Contents for MerCruiser Axius SeaCore 350 MAG

Reviews:

Related manuals for MerCruiser Axius SeaCore 350 MAG

Brands by name

Popular brands

Mercury MerCruiser Axius SeaCore 350 MAG, Manual

Search results

Summary of Contents for MerCruiser Axius SeaCore 350 MAG

Reviews:

Related manuals for MerCruiser Axius SeaCore 350 MAG

Brands by name

Popular brands