manualshive.com logo in svg

Mercury 1997 Sable, Owner'S Manual

Share
Download
Mercury 1997 Sable Owner'S Manual Download Page 83

Pull release handle
toward you to release
parking brake. Driving
with the parking brake
on will cause the
brakes to wear out
quickly and reduce fuel
economy.

TRANSAXLE

Brake-shift interlock

This vehicle is equipped with a brake-shift interlock
feature that prevents the gearshift from being moved
from P (Park) unless the brake pedal is pressed.

If you cannot move the gearshift out of P (Park)
with the brake pedal depressed:

1. Apply the parking brake, turn ignition key to
LOCK, then remove the key.

2. Insert the key and turn it to OFF. Apply the brake
pedal and shift to N (Neutral).

3. Start the vehicle.

If it is necessary to use the above procedure to
move the gearshift, it is possible that a fuse has
blown and the vehicle’s brake lamps may not be
operating properly. Refer to

Fuses and relays

in the

Roadside emergencies

chapter.

Do not drive your vehicle until you verify
that the brakelamps are working.

If your vehicle gets stuck in mud or snow it may be
rocked out by shifting from forward and reverse
gears in a steady pattern. Press lightly on the

dno_transaxle

dno_bsi

Driving

83

Summary of Contents for 1997 Sable








































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands