manualshive.com logo in svg

Mercury 1997 Sable, Owner'S Manual

Share
Download
Mercury 1997 Sable Owner'S Manual Download Page 69

8. Allow the safety belt
to retract to remove
any slack in the belt.

9. Before placing the
child in the seat,
forcibly tilt the seat
forward and back to
make sure the seat is
securely held in place.

10. Try to pull the belt out of the retractor to make
sure the retractor is in the automatic locking mode
(you should not be able to pull more belt out). If the
retractor is not locked, unbuckle the belt and repeat
steps two through nine.

Check to make sure the child seat is properly
secured before each use.

Attaching safety seats with tether straps

Some manufacturers make safety seats that include
a tether strap that goes over the back of the vehicle
seat and attaches to an anchoring point. Other
manufacturers offer the tether strap as an accessory.
Contact the manufacturer of your child safety seat
for information about ordering a tether strap.

Front seats

To install a tether from a child safety seat in the
front seat:

1. Buckle the lap/shoulder belt (in the seat behind
the front passenger seat in which the child safety
seat will be installed).

2. Pull all the stored belt out of the rear seat
retractor to switch the retractor to automatic locking
mode.

3. Let the retractor wind up the slack from the
lap/shoulder belt.

4. Install the child safety seat in the front seat. Refer
to

Installing child safety seats in combination lap

and shoulder belt seating positions

. Hook the

dno_tether-straps

Seating and safety restraints

69

Summary of Contents for 1997 Sable








































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands