manualshive.com logo in svg

Mercury 1997 Sable, Owner'S Manual

Share
Download
Mercury 1997 Sable Owner'S Manual Download Page 59

safety belt assembly by adding a safety belt
extension assembly (part number 611C22). Safety
belt extension assemblies can be obtained from your
dealer at no cost. This assembly is not for use in the
wagon’s rear-facing seat.

Use only extensions manufactured by the same
supplier as the safety belt. Manufacturer
identification is located at the end of the webbing on
the label. Also, use the safety belt extension only if
the safety belt is too short for you when fully
extended. Do not use extensions to change the fit of
the shoulder belt across the torso.

Safety belt warning light and indicator chime

The seat belt warning light illuminates in the
instrument cluster and a chime sounds to remind
the occupants to fasten their safety belts.

Conditions of operation

If...

Then...

The driver’s safety
belt is not buckled
before the ignition
key is turned to ON...

The safety belt indicator
illuminates for one to two
minutes and the warning
chime sounds for four to
eight seconds.

The driver’s side
safety belt is buckled
while the indicator
light is illuminated
and the warning
chime is sounding...

The safety belt indicator
light and warning chime
turn off.

The driver’s safety
belt is buckled before
the ignition key is
turned to ON...

The safety belt warning
light and indicator chime
remain off.

dno_warning-light-and-chime

dno_operation

Seating and safety restraints

59

Summary of Contents for 1997 Sable








































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands