manualshive.com logo in svg

Mercury 1997 Sable, Owner'S Manual

Share
Download
Mercury 1997 Sable Owner'S Manual Download Page 8

you should check the coolant level inside the
reservoir. For instructions on adding coolant, see

Engine coolant

in the index.

Anti-theft alarm light (if equipped)

This light is used when
you set the anti-theft
alarm system. See

Anti-theft system

in

the index.

O/D off (if equipped)

Illuminates when the
transaxle control
switch (TCS) has been
pushed. When the light
is on, the transaxle does not shift into overdrive. If
the light does not come on when the TCS is
depressed or if the light flashes when you are
driving, have your vehicle serviced.

Anti-lock brake system (ABS) (if equipped)

Momentarily illuminates
when the ignition is
turned on and the
engine is off. If the
light stays on or continues to flash, the ABS needs
to be serviced.

Cruise control (if equipped)

This light comes on
when the cruise control
ON button is pressed.
It turns off when the
cruise control OFF
button is pressed or when the ignition is turned to
the OFF position.

THEFT

O/D

OFF

ABS

CRUISE

dno_theft

dno_overdrive-off

dno_abs

dno_cruise-light

com_brake_system.01

Instrumentation

8

Summary of Contents for 1997 Sable








































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands