Mercury 1997 Sable Owner'S Manual Download Page 134

Page: 134 / 167

•

The suspension insulation and bumpers will help
prevent vehicle damage. Do not remove these
components from your vehicle when using snow
tires and chains.

WHAT YOU SHOULD KNOW ABOUT
AUTOMOTIVE FUELS

Important safety precautions

Do not overfill the fuel tank. The pressure in
an overfilled tank may cause leakage and

lead to fuel spray and fire.

If you do not use the proper fuel cap, the
pressure in the fuel tank can damage the

fuel system or cause it to work improperly in a
collision.

The fuel system may be under pressure. If
the fuel cap is venting vapor or if you hear a

hissing sound, wait until it stops before completely
removing the cap.

Automotive fuels can cause serious injury or
death if misused or mishandled.

Observe the following guidelines when handling
automotive fuel:

dno_fueling

com_important_precautions.06

Maintenance and care

134

Summary of Contents for 1997 Sable








































































































































































Search results

Summary of Contents for 1997 Sable

Reviews:

Brands by name

Popular brands

Mercury 1997 Sable, Owner'S Manual

Search results

Summary of Contents for 1997 Sable

Reviews:

Brands by name

Popular brands