manualshive.com logo in svg

Mercury 1997 Sable, Owner'S Manual

Share
Download
Mercury 1997 Sable Owner'S Manual Download Page 24

You can accelerate with the accelerator pedal at any
time during cruise control usage. Releasing the
accelerator pedal will return your vehicle to the
previously programmed set speed.

To set a lower set speed

•

Press and hold
COAST. Release the
control when the
desired speed is
reached or

•

Press and release
COAST. Each press
will decrease the set
speed by 1.6 km/h (1 mph) or

•

Depress the brake pedal. When the desired
vehicle speed is reached, press SET ACCEL.

To disengage cruise control

•

Depress the brake pedal.

Disengaging the cruise control will not erase the
previously programmed set speed.

Pressing OFF will erase the previously programmed
set speed.

To return to a set speed

•

Press RESUME. For
RESUME to operate,
the vehicle speed
must be faster than
48 km/h (30 mph).

ON

OFF

COAST

RESUME

SET

ACCEL

ON

OFF

COAST

RESUME

SET

ACCEL

dno_tap-down-feature

dno_disengage

dno_resume-feature

dno_cruise-light

Controls and features

24

Summary of Contents for 1997 Sable








































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands