manualshive.com logo in svg

Mercury 1997 Sable, Owner'S Manual

Share
Download
Mercury 1997 Sable Owner'S Manual Download Page 135

•

Extinguish all
smoking materials
and any open flames
before fueling your
vehicle.

•

Always turn off the
vehicle before
fueling.

•

Automotive fuels can be harmful or fatal if
swallowed. If fuel is swallowed, call a physician
immediately, even if no symptoms are immediately
apparent. The toxic affects of fuel may not be
visible for hours.

•

Fuels can also be harmful if absorbed through the
skin. If fuel is splashed on the skin, promptly
remove contaminated clothing and wash skin
thoroughly with soap and water.

•

If fuel is splashed in the eyes, remove contact
lenses, flush with water for 15 minutes and seek
medical attention.

•

Be particularly careful if you are taking
“Antabuse” or other forms of disulfiram for the
treatment of alcoholism. Breathing gasoline vapors
or skin contact could cause an adverse reaction.
Consult a physician immediately.

Choosing the right fuel

Use only UNLEADED FUEL. The use of leaded fuel
is prohibited by law and could damage your vehicle.
The damage may not be covered by your warranty.

Your vehicle was not designed to use fuel containing
manganese-based additives such as MMT.
Additionally, vehicles certified to California emission
standards (indicated on the underhood Vehicle
Emissions Control Information label) are designed to
operate on California reformulated gasolines. If
California reformulated gasoline is not available
when you refuel, your vehicle can be operated on
non-California fuels. However, even though your

com_choosing_fuel.01

Maintenance and care

135

Summary of Contents for 1997 Sable








































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands