manualshive.com logo in svg

Mercury 1997 Sable, Owner'S Manual

Share
Download
Mercury 1997 Sable Owner'S Manual Download Page 62

HOW DOES THE AIR BAG SUPPLEMENTAL
RESTRAINT SYSTEM WORK?

The SRS is designed to
activate when the
vehicle sustains
sufficient longitudinal
deceleration, similar to
hitting a fixed barrier
head on at 12–24 km/h
(8–14 mph).

The fact that the air
bags did not inflate in
a collision does not
mean that something is
wrong with the system. Rather, it means the forces
were not of the type sufficient to cause activation.

The air bags inflate and
deflate rapidly upon
activation.

After air bag
deployment, it is
normal to notice a
smoke-like, powdery
residue or smell the
burnt propellant. This
may consist of
cornstarch, talcum
powder (to lubricate
the bag) or sodium compounds (e.g., baking soda)
that result from the combustion process that inflates
the air bag. Small amounts of sodium hydroxide may
be present which may irritate the skin and eyes, but
none of the residue is toxic.

Several air bag system components get hot
after inflation. Do not touch them after

inflation.

com_how_work.01

Seating and safety restraints

62

Summary of Contents for 1997 Sable








































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands