manualshive.com logo in svg

Mercury 1997 Sable, Owner'S Manual

Share
Download
Mercury 1997 Sable Owner'S Manual Download Page 66

You may wish to discuss the special needs of your
child with your pediatrician.

SAFETY SEATS FOR CHILDREN

Child and infant or child safety seats

Use a safety seat that is recommended for the size
and weight of the child. Carefully follow all of the
manufacturer’s instructions with the cafety seat you
put in your vehicle. If you do not install and use the
safety seat properly, the child may be injured in a
sudden stop or collision.

When installing a child safety seat:

•

Use the correct
safety belt buckle
for that seating
position.

•

Make sure the
tongue is securely
fastened in the
buckle.

•

Keep the buckle release button pointing up and
away from the safety seat, with the tongue
between the child seat and the release button, to
prevent accidental unbuckling.

•

Place seatback in upright position.

•

Put the safety belt in the automatic locking mode.
Refer to

Using the automatic locking mode.

Ford recommends the use of a child safety seat
having a top tether strap. Install the child safety seat
in a seating position which is capable of providing a
tether anchorage. For more information on top
tether straps, refer to

Attaching safety seats with

tether straps

.

dno_child-belt

dno_child-safety-seats

Seating and safety restraints

66

Summary of Contents for 1997 Sable








































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands