manualshive.com logo in svg

Mercury 1997 Sable, Owner'S Manual

Share
Download
Mercury 1997 Sable Owner'S Manual Download Page 70

tether strap hook around the webbing near the
center of the shoulder portion of the locked
lap/shoulder belt.

5. Tighten the tether strap.

Rear seats

If you must use a tethered safety seat on one of the
rear seats, you can anchor the strap to the
appropriate tether anchor directly behind that seat
position.

Tether anchorage hardware

Attachment holes (at each rear outboard seating
position) have been provided in your vehicle to
attach anchor hardware, if required. Tether
anchorage hardware kits (part number 613D74)
including instructions, may be obtained at no charge
from any Ford or Lincoln-Mercury dealer. All
vehicles built for sale in Canada include a tether
anchor hardware kit.

Be sure to follow the child safety seat
manufacturer’s instructions.

Tighten the anchor according to
specifications. Otherwise, the safety seat

may not be properly secured and the child may be
injured in a sudden stop or collision.

If you have a station wagon, tether anchors are
already installed for each of the second row seating
positions.

1. Behind the second
seat, find the plastic
snap-on covers for the
floor anchors.

dno_hardware

Seating and safety restraints

70

Summary of Contents for 1997 Sable








































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands