mensor CPC4000 Operating Instructions Manual Download Page 70

Page: 70 / 114

Operating Instructions - CPC4000

Industrial Pressure Controller

CPC4000

DHCP

ON or OFF

Reserved for DHCP setup

DHCP?

Reserved for DHCP setup

DOC

mm/dd/yyyy

Sets the date of cal for the active

transducer.

DOC?

Returns the date of cal for the active

transducer.

DOM?

Returns the date of manufacture

Error?

<sp> text description <cr><lf>

Returns the next error in the error

queue

Errorno?

Returns pcs400 error code and text

Filter

OFF, LOW, NORMAL, HIGH

Sets the reading filter 0, 80%, 92%,

95%

Filter?

<sp> (filter)<cr><lf>

Returns the reading filter.

Gasdensity

Value in lb/cuft, or “NITROGEN” or

“DRYAIR”

Sets the head pressure gas density in

lb/cuft

Gasdensity?

Gets the head pressure gas density in

lb/cuft

Gastemp

Value in degrees F

Sets the head pressure gas tempera-

ture

Gastemp?

<lf>

Gets the head pressure gas tempera-

ture

Gateway

nnn.nnn.nnn.nnn

Sets the Ethernet gateway address

Gateway?

Gets the Ethernet gateway address

Height

Value in inches

Sets the head pressure height in

inches

Height?

<lf>

Gets the head pressure height in

inches

Highspeed

ON or OFF

Sets the highspeed control mode,

which sets the control behavior, stable

window, stable delay, and rate set-

point

Highspeed?

Returns the status of the highspeed

mode

Id?

<sp>MENSOR,CPC4000,

ssssss,v.v.vv<cr><lf>

Ssssss is the serial number,v.v.vv is

the CPC 4000 software version.

Instrument_control_

time_on?

<sp>NNNNN<cr><lf>

Returns the amount of time the instru-

ment has been in control mode since

the last reset of the counter, in min-

utes

Instrument_total_con-

trol_time_on?

<sp>NNNNN<cr><lf>

Returns the lifetime amount of time

the instrument has been in control

mode, in minutes

Instrument_time_on? <sp>NNNNN<cr><lf>

Returns the amount of time the instru-

ment has been on since the last reset

of the counter, in minutes

Summary of Contents for CPC4000



















































































































Search results

Summary of Contents for CPC4000

Reviews:

Related manuals for CPC4000

Brands by name

Popular brands

mensor CPC4000, Operating Instructions Manual

Search results

Summary of Contents for CPC4000

Reviews:

Related manuals for CPC4000

Brands by name

Popular brands