mensor CPC4000 Operating Instructions Manual Download Page 69

Page: 69 / 114

Operating Instructions - CPC4000

Industrial Pressure Controller

CPC4000

Burst_Slow

value inside upper and lower limits

This is the rate used during the transi-

tion from low setpt to high setpt in the

anticipated “burst range”

Burst_Slow?

Returns the slow rate for burst test

Burst_Fast

value inside upper and lower limits

This is the rate used during the transi-

tion from atmosphere to the low setpt

Burst_Fast?

Returns the fast rate for burst test

Burst_Result?

Pressure at which burst was detected.

Will return 0 if no burst found.

Calculate_as_found_

line arity

Calculate linearity slopes and inter-

cepts from true/actual pressures

Caldisable

YES,NO

Sets whether or not calibration of the

active transducer is disabled.

Caldisable?

Returns whether or not calibration of

the active transducer is disabled.

Calibration_mode?

Returns the current calibration mode

setting

Calibration_mode

YES, NO

Enable/ disable the calibration mode,

which when on, disables the sensor

overpressure error and forces range

hold to lock the secondary shutoff

valve. Normally the secondary range

is always allowed to go to its maxi-

mum pressure to avoid a large pres-

sure disturbance when switching to it.

Cerr

None

Clears the error queue

Cmdset

Mensor, DPI510, SCPI

Activates remote command set for

instrument emulation modes.

Cmdset?

Returns active command set identifier

Control

Instrument placed in Control Mode

Control?

Returns YES if instrument is in control.

NO if otherwise

Control_behavior <n> 0 to 100

100 = highspeed, 0 = low overshoot.

May be set between 0 and 100.

Control_behavior?

Returns the control behavior number

Crate

Slow, Medium, Fast, Variable

Sets the control rate, Variable mode

is a predetermined user defined rate

setpt.

Crate?

<sp>CCCCCC<cr><lf>

Returns the control rate – CCCC is

variable in length and corresponds to

the parameters for the CRATE com-

mand

Ctype?

Returns the type of regulator

Decpt?

Returns the number of decimal points

(see Resolution)

Default

None

Sets the default values

Summary of Contents for CPC4000



















































































































Search results

Summary of Contents for CPC4000

Reviews:

Related manuals for CPC4000

Brands by name

Popular brands

mensor CPC4000, Operating Instructions Manual

Search results

Summary of Contents for CPC4000

Reviews:

Related manuals for CPC4000

Brands by name

Popular brands