mensor CPC4000 Operating Instructions Manual Download Page 74

Page: 74 / 114

Operating Instructions - CPC4000

Industrial Pressure Controller

CPC4000

Reset_instrument_

control_time_on

Resets the instrument’s time on coun-

ter. See usage application for more

details

Resolution

<n>

Sets the number of significant digits.

(see decpt)

Resolution?

Returns the number of significant

digits.

(see decpt)

Rfilter

Value in %

Sets the % of the rate filter

Rfilter?

<lf>

Returns the rate filter.

Rsetpt

Value in current units

Sets the rate setpoint

Rsetpt?

<lf>

Returns the rate setpoint

Runits

Sec, min, hr

Sets the rate time unit

Runits?

Returns the rate time unit

Save_cal

Save calibration values

Save_linearity

Save linearity values

Sbaud

9600, 19200, 38400, 57600, 115200

Sets the serial baud rate

Sbaud?

Returns the serial baud data

Sdata

7 or 8

Sets the serial data bits

Sdata?

Returns the serial data bits number

Sensor

1,2, P,S, PRIMARY, SECONDARY

Sets the active transducer. Accepts

multiple format types.
Sensor may be specified with P, S, 1

or 2.

Sensor?

<sp>XXXXXXX,1<cr><lf>

Returns active transducer in long

string format

Sensorid?

<sp>Mensor,SN XXXXXX, VN.NN

Returns the active transducer’s serial

number and firmware version

Setpt

value inside upper and lower limits

Sets the control setpoint for the instru-

ment

Setpt?

<sp>XXXXXXX<cr><lf>

Returns the control setpoint in current

units.

Setpt%

Value in % of current range

Sets the control setpoint in % of cur-

rent range

Setptpct

Value in % of current range

Sets the control setpoint in % of cur-

rent range

Setptpct?

<lf>

Returns the current setpoint in % of

current range

Span

desired pressure or ?

Sets span on active transducer or for

?, clears previous value, must be >

50% FS and has a 1% limit. CALDIS-

ABLE must be OFF/NO.

Summary of Contents for CPC4000



















































































































Search results

Summary of Contents for CPC4000

Reviews:

Brands by name

Popular brands

mensor CPC4000, Operating Instructions Manual

Search results

Summary of Contents for CPC4000

Reviews:

Brands by name

Popular brands