mensor CPC4000 Operating Instructions Manual Download Page 64

Page: 64 / 114

Operating Instructions - CPC4000

Industrial Pressure Controller

CPC4000

7.3 Ethernet
The Ethernet function allows the user to set the following by inputting a numeric value in each separate

field:
•  IP
•  Netmask
•  Gateway
•  Port
•  DHCP settings
Set the Ethernet communication parameters as described in Section 6.4.9.

Caution

CAUTION: Please contact your network administrator for proper settings.

Caution

CAUTION: Please consult your computer resources department prior to connect-

ing this instrument to your network to verify there are no conflicts with existing IP

addresses.

The Ethernet communication port allows the CPC4000 to communicate with computers using

10/100Based-T specifications.
Before using Ethernet communication, four parameters must be set up: IP, Netmask, Gateway, and Port.

Summary of Contents for CPC4000



















































































































Search results

Summary of Contents for CPC4000

Reviews:

Related manuals for CPC4000

Brands by name

Popular brands

mensor CPC4000, Operating Instructions Manual

Search results

Summary of Contents for CPC4000

Reviews:

Related manuals for CPC4000

Brands by name

Popular brands