Meltem M-WRG-S/Z-24 Installation Manual Download Page 5

Page: 5 / 32

Installation manual

M-WRG-S/Z-S, M-WRG-S/Z-24,

M-WRG-S/Z-EIB, M-WRG-S/Z-KNX (-F, -FC)

- 5 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L AT I O N & H E AT R E C O V E R Y

1 Introduction

1.1

Notes on this installation manual

This installation manual contains important information that should be followed when connect-

ing the control cables / bus cables to the M-WRG-S/Z-S, M-WRG-S/Z-24, M-WRG-S/Z-EIB and

M-WRG-S/Z-KNX (-F, -FC) ventilation units.

►

Read all the instructions carefully before installing to avoid possible risks and mistakes.

►

When installation is complete, give these instructions to the home owner, caretaker or

property manager.

►

These instructions are part of the product. Keep the instructions in a safe place for future

reference.

WARNING

►

Follow ALL danger and warning instructions and notes on precautionary measures.

►

Read section „2 Safety instructions“ on page 6 carefully.

NOTE

►

Also follow the installation manual M-WRG-S.../M-WRG-K..., part no. 5300-10-01 (see sec-

tion 1.6 on page 6), for installing the ventilation units.

1.2

Description

This manual describes how to connect the control cables / bus cables to the following ventilation

units:

—

Connecting the M-WRG-S/Z-S to the control cable (see section 6 from page 8)

—

Connecting the M-WRG-S/Z-24 to the control cable (see section 7 from page 13)

—

Connecting the M-WRG-S/Z-EIB to the EIB universal interface 6119/40 and EIB bus cable

(see section 8 from page 16)

—

Connecting the M-WRG-S/Z-KNX (-F, -FC) to the KNX bus cable (see section 9 from

page 21)

1.3

Target group

The activities described in this manual must only be carried out by technicians with the following

qualifications:

—

Training in the installation and commissioning of electrical devices

—

Training in electrical hazards and the local safety requirements

—

Knowledge of the relevant standards and directives

—

Knowledge and observance of this document and all the safety instructions

Summary of Contents for M-WRG-S/Z-24

































Search results

Summary of Contents for M-WRG-S/Z-24

Reviews:

Related manuals for M-WRG-S/Z-24

Brands by name

Popular brands

Meltem M-WRG-S/Z-24, Installation Manual

Search results

Summary of Contents for M-WRG-S/Z-24

Reviews:

Related manuals for M-WRG-S/Z-24

Brands by name

Popular brands