Meltem M-WRG-S/Z-24 Installation Manual Download Page 7

Page: 7 / 32

Installation manual

M-WRG-S/Z-S, M-WRG-S/Z-24,

M-WRG-S/Z-EIB, M-WRG-S/Z-KNX (-F, -FC)

- 7 -

Meltem Wärmerückgewinnung GmbH & Co. KG

Am Hartholz 4 · D-82239 Alling

[email protected] · www.meltem.com

VENTILATION THE RIGHT WAY

V E N T I L AT I O N & H E AT R E C O V E R Y

2.2

Notes on using the ventilation units safely

CAUTION

—

Starting and using the ventilation unit

►

Do not start up the ventilation unit until it is fully installed.

►

Always make sure that the cover is closed and locked in place before using the venti-

lation unit.

2.3

Intended use

—

The intended use includes compliance with all the notes in the installation manual.

—

The ventilation unit must not be operated without air filters.

—

For any use contrary to the intended use, Meltem Wärmerückgewinnung GmbH & Co.

KG shall accept no liability for any damage that may occur and offers no warranty that the

components will work perfectly and correctly.

3 Warranty and liability

The warranty and liability shall be void if the ventilation unit is not connected as described in this

installation manual.

4 Tools and equipment required

—

Set of cross-head screwdrivers

—

Set of slotted screwdrivers

5 Codes for designation of wire colours

Colour

Code as per IEC 60757

Black

Brown

Red

Orange

Yellow

Green

Blue

Violet

Grey

White

Table 1: Codes for designation of wire colours

Summary of Contents for M-WRG-S/Z-24

































Search results

Summary of Contents for M-WRG-S/Z-24

Reviews:

Related manuals for M-WRG-S/Z-24

Brands by name

Popular brands

Meltem M-WRG-S/Z-24, Installation Manual

Search results

Summary of Contents for M-WRG-S/Z-24

Reviews:

Related manuals for M-WRG-S/Z-24

Brands by name

Popular brands