Meler Micron PUR LC Instruction Manual Download Page 57

Page: 57 / 106

MELTER OPERATION

4-23

MA-5184-ENG

PUR LC/MC ADHESIVE MELTER

ENGRANE

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

: S02101100 v1.0.106

10 min

1.4 Auto Standby - OFF

Standby desactivation

Activity control

Standby due to lack of recharge

Standby

OFF

ENGRANE

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

: S02101100 v1.0.106

XDI1

XDI2

DI3

DO2

XDO3

XDO4

2.3 Input / Output

Imputs

Outputs

Standby

ON / OFF

Temperature OK

Alarms

Adhesive Level

Activity

1.4 Auto Standby - OFF

This function can program the following work parameters:

• Standby Deactivation:

automatically deactivates the ‘General Standby’

mode activated manually. Once the minutes programmed in the unit have

passed, the heating process will start again.

If the ‘Calendar’ is active, the unit will follow the programmed calendar.

• Activity control: This lets you configure the times for changing to Stan-

dby mode and to Inhibition (OFF) when the activity signal ceases.

The activity of the line is monitored from a digital input. When it detects

that there is no activity, the unit changes to Standby mode after the

programmed time has passed, and changes to Inhibition mode when the
second time has passed.

• Standby due to lack of recharging:

the equipment automatically switches to

Standby when it detects a lack of adhesive and has not detected a recharge

after the programmed time.

PISTÓN

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

C1 C2 C3 C4 C5 C6

Calendar

Hour

Standby

OFF

07:00

11:00

13:15

15:00

00.00

Enable all the calendars

Modo ON

Standby

OFF

Piece

Main machine production

Standby

Off

PISTÓN

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

Group OFF

OFF Group: 1

Temperature

State

Area

Standby

OFF

T: Tank

D: Distributor

1.1: Hose 1

1.2: Applicator 1

2.1: Hose 2

2.2: Applicator 2

General Standby

General OFF

PISTÓN

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

10 min

1.4 Auto Standby - OFF

Standby desactivation

Activity control

Standby due to lack of recharge

Standby

OFF

PISTÓN

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

XDI1

XDI2

DI3

DO2

XDO3

XDO4

2.3 Input / Output

Imputs

Outputs

Standby

COMs OFF

Pump OFF

Temperature OK

Alarms

Adhesive Level

PISTÓN

HMI

: S02001100 v1.0.106

: S02200100 v1.0.084

: S02102100 v1.0.106

XDI1

XDI2

DI3

DO2

XDO3

XDO4

2.3 Input / Output

Imputs

Outputs

Standby

ON / OFF

Temperature OK

Alarms

Adhesive Level

Activity

Piece

Piece Piece

Piece

Summary of Contents for Micron PUR LC











































































































Search results

Summary of Contents for Micron PUR LC

Reviews:

Brands by name

Popular brands

Meler Micron PUR LC, Instruction Manual

Search results

Summary of Contents for Micron PUR LC

Reviews:

Brands by name

Popular brands