manualshive.com logo in svg

Meler Micron PUR LC, Instruction Manual

Share
Download
Meler Micron PUR LC Instruction Manual Download Page 43

MELTER OPERATION

4-9

MA-5184-ENG 

  PUR LC/MC ADHESIVE MELTER

Alarms status

There are no errors.

The unit has an operating error but can continue operating.

The unit has an operating error and cannot continue operating.

Access the ALARMS menu by pressing the icon.

Calendar status

Adhesive level status

Calendar not activated.

Calendar activated

Access the CALENDAR menu by pressing the icon.

•  WITHOUT automatic loading

•  WITHOUT level sensor  

•  WITH automatic loading

•  Adhesive level nearly empty 

•  WITH automatic loading 

•  Adhesive level nearly empty and 

LOADING  

•  WITHOUT automatic loading 

•  WITH level sensor.  

Adhesive level nearly empty 

•  WITH automatic loading 

•  Adhesive level sufficient and 

LOADING (extra time)

•  WITHOUT automatic loading 

•  WITH level sensor.  

Adhesive level sufficient 

•  WITH automatic loading 

•  Adhesive level sufficient

Summary of Contents for Micron PUR LC











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands