Maxwell MW-1754 W, Manual Instruction

Page: 10 / 28

10
ENGLISH
•
Tilt the thermopot carefully and pour the
remaining water out of the flask.
Note:
– To remove foreign smells, boil and pour out
water 2-3 times.
Attention! Be careful when pouring out water
to avoid scalding by steam and hot water.
USING THERMOPOT
•
Open the lid (11) by pressing the button (6)
and holding it.
•
Fill the thermopot with water using a suitable
bowl, do not exceed the maximal water level
mark (14) «FULL» on the inner surface of the
thermopot flask.
• Insert the power cord (17) connector into
the socket (16) on the thermopot body, and
the power plug into the mains socket. The
thermopot will switch on in boiling mode, the
«Boiling» indicator (19) will light up on the
control panel (5).
• After water starts boiling, the thermopot will
be switched to the keep warm mode, the
«Keep warm» indicator (20) will light up.
• You can re-boil water after a while, when the
unit is in the keep warm mode and the «Keep
warm» indicator (20) lights on the control
panel. Press the «Repeat» button (21), the
«Boiling» indicator (19) will light up.
• When using the thermopot, ensure that the
water level is not below the «Empty» mark
(1) and not above the «FULL» mark (14).
If the water level gets below the «Empty»
mark (1), open the lid (11) and refill the ther-
mopot with water.
• Pour boiled water into a suitable bowl, having
placed it under the spout (4).
•
To dispense hot water, press and hold down
the button (22) «Dispense».
•
You can also dispense water using the hand
pump (7) having previously set the hand
pump lock (10) to the position «
».
•
After use disconnect the unit from the mains
by removing the plug of the power cord (17)
from the mains socket and detaching the
power cord from the socket (16).
•
To pour out the remaining water, wait until
the unit cools down completely. While keep-
ing the lid (11) closed, press the lock (9) and
remove the lid upwards as you hold the but-
ton (6).
•
Tilt the thermopot carefully and pour the
remaining water out of the flask.
•
To install the lid (11) back to its place, press
the lock (9), insert the metal axle of the lid
(11) into the notch of the lock (9) and release
the lock (9).
CLEANING AND CARE
•
Before cleaning, disconnect the unit from the
mains, let the thermopot cool down and pour
out water.
•
Clean the thermopot outer surface with a
soft damp cloth and then wipe it dry. Do not
use metal brushes, abrasives and solvents to
clean the thermopot.
• Do not immerse the thermopot, the power
cord and the power plug into water or other
liquids.
•
Do not wash the thermopot in a dishwashing
machine.
Stains on the inner surface
of the thermopot
The inner metal surface may change its color
under the influence of different water impurities.
• To remove the stains, wet a cloth with citric
acid or vinegar and wipe the inner surface of
the thermopot flask.
• To remove the citric acid or vinegar taste,
boil water and pour it out. Repeat this pro-
cedure until the smell and taste vanish
completely.
Descaling
•
Scale, appearing inside the thermos kettle,
influences the water taste and disturbs the
heat exchange between water and heating
element that can lead to overheating and
malfunction.
• To remove scale, fill the thermos kettle with
a mixture of one part ordinary vinegar and
two parts water up to the maximal water level
mark. Boil the liquid and leave it in the unit
overnight. In the morning pour out the liquid,
fill the thermos kettle with water up to the
maximal water level mark, boil and pour the
water out.
• You can use special detergents for electric
kettles to remove scale.
• After descaling, boil and pour out clean water.
DELIVERY SET
Thermopot – 1 pc.
Power cord – 1 pc.
Instruction manual – 1 pc.
MW-1754.indd 10 06.09.2018 12:45:58