10
ENGLISH
INSTALLING THE TELESCOPIC
ATTACHMENT
–
Before installing or removing the telescopic
attachment (1) switch the unit off by setting
the switch (4) to the position «0»; if the unit
is powered by the mains, unplug the power
adapter (7).
–
Match the ledges on the attachment (1) with
the grooves on the hair clipper body and
install the attachment (1) back to its place.
–
Adjust the attachment (1) position by moving
the attachment (1) relative to the mark on the
hair clipper body.
–
After you set the required cutting length fix
the attachment (1) by setting the clamp (3) in
the upper position.
HAIR STYLING INSTRUCTIONS
•
Hair should be clean and dry during hair cut-
ting.
•
Before cutting hair switch the hair clipper
on by setting the switch (4) to the position
«I» and make sure that hair clipper operates
normally and the blades move smoothly. If
there is excess oil on the blades, switch the
hair clipper off setting the power switch (4)
to the position «0» and remove the excessive
oil with a dry cloth.
•
During the operation with the unit connected
to the power adapter (7) always check the
power adapter cord condition, do not allow
its multiple twisting, periodically turn the unit
off and straighten the power adapter cord.
•
Seat a person so that his/her head is approxi-
mately at your eye level, cover the person’s
shoulders with a towel and set hair with the
comb (11).
Reminder
–
Always cut off a little amount of hair at a time;
if necessary you can always return to the cut
off part and trim off additional hair.
–
The best haircutting results are reached on
dry hair, not wet.
–
Comb the hair with a comb (11) to reveal
uneven locks.
–
It is better to leave longer hair after cutting
for the first time.
–
After learning your clipper better, you will be
able to arrange your hair in any style you need.
Step one
Install the telescopic attachment (1), set it to the
cutting length position «3 – 5» and fix it with the
clamp (3). Switch the unit on using the power
switch (4), setting it to position «I». Hold the hair
clipper with the blades pointed upwards. Start
cutting from the beginning of the hair growth.
Slowly move the trimmer upwards. This way cut
the head back area at neck bottom and near the
ears.
Step two
Switch the hair clipper off using the switch (4)
by setting it to the position «0» and set the tele-
scopic attachment (1) for cutting longer hair to
the position «6 - 9», switch the hair clipper on and
continue cutting hair near the top of the head.
Step 3 – cutting in the temples area
Switch the hair clipper off, set the telescopic
attachment (1) to the position «3 - 6» for shorter
hair and cut hair on the temples. Then set the
telescopic attachment (1) to the position 9 - 12
and continue cutting towards the top of the head.
Step 4 – cutting the crown of the head
Using the telescopic attachment (1) set it to the
position «9 – 12» and cut the hair from the top
of the head towards the crown against the hair
growth direction.
•
You can cut hair against and along the direc-
tion of hair growth, but keep in mind that the
hair cut against the growth will be shorter
than the hair cut along the growth.
•
Use the telescopic attachment (1) position
«3 - 6» for very short cutting. To leave a little
longer hair, use the telescopic attachment
(1) position «9 – 15».
•
To leave longer hair, take hair locks between
your fingers and cut hair using the hair clipper.
•
You can use the comb: lift the hair locks and
cut them with the hair clipper above the comb.
•
Always start cutting from the head back.
•
Comb the hair to reveal uneven locks.
Step 5 – the final part
In the final stage of hair cutting remove the
telescopic attachment (1) from the unit, turn
the blades of the clipper towards the hair and
trim hair on the temples and neck carefully. Do
not press the clipper strongly, there is danger
of injuries or cuts when open blades come in
contact with skin.
Note: during the breaks between operations
switch the hair clipper off, setting the power
switch (4) to the position «0».
MW-2114.indd 10
27.07.2017 14:21:25
Summary of Contents for 89839
