background image

 

113 

 

Figure 8-7 

Sample System Settings Screen 

3.  Tap the 

App Switcher 

option on the left column. 

4.  Mark the checkbox beside “Always show the App Switcher” on the 

right side of the screen, then the App Switcher icon shows. 

Short pressing the App Switcher icon opens a control panel:   

  Tapping a specific app shortcut button enables you to switch directly to 

the selected application screen. 

  Long pressing a specific app shortcut button displays the app menu, 

on which you can select and change the app shortcut. 

  Pressing  and  dragging  the  App  Switcher  icon  around  allows  you  to 

change the icon position alongside the edge of the screen. 

You  may  refer  to  Android  documentation  for  additional  information  about 

Android system settings. 

About 

The About option provides information of the MaxiCheck diagnostic device 

regarding the product name, version, hardware, and serial number, etc. 

 

To check the MaxiCheck product information in About 

1.  Tap the 

Settings 

application on the MaxiCheck Job Menu. 

2.  Tap the

 About 

option on the left column. The product information 

screen displays on the right. 

Summary of Contents for MX808TS













































































































































































Reviews: