Max 1500 PRO, Installation Manual

Page: 7 / 40

Step-By-Step Installation
Operator Placement (Standard)
Connect Chain to Gate (Standard)
Rear Mounting Position (Alternate)
Connect Chain to Gate (Rear Pos)
AC Input Power
Ground Operator
Opening Direction/ID Plug/Operator
Entrapment Protection Wiring
Program Virtual Limit Sensors
Learn Gate Positions
Adjust ERD Reverse Sensor
Loops & Loop Detectors
Matrix III Settings
Wiring Opening Device Options
Learn Unlearned Sensor Inputs
1
2
3
4
5
6
6
7-8
9
10
10
11
11
12
12
Table of Contents
specifications
Additional Features
Programming
DIP-Switch
Settings
Gate Shut-Off Switch
Electronic Gate OPEN / CLOSE
Gate Tamper Feature
Dropping the Chain - Gate Tamper is Armed (ON)
Dual Gate Operators Wiring
Gate Disable Feature
13
13
14
14
15
16
17
18
Gate Safety
UL 325 Compliant Installation Requirements
UL 325 Model Classifications
Intended Use of Slide Gate Operator
Safety-1-3
Safety-4
Safety-5
Troubleshooting
USB Black Box Port
Test Entrapment Sensors
Gate Cycling Troubleshooting
Matrix III LED Troubleshooting
Commonly Used Safety Sensors
Omron E3K-R10K4
Omron IRB-RET
EMX IRB-MON Single Gate
EMX IRB-MON Dual Gates
Miller RBAND Monitored Wireless
Wiring Overview
Optional Magnet Limit Sensors
Optional Solar Power
19
19
20
21-22
23
23
24
25
26
27
28
29
UL 325 Class of Operation - MAX 1500 PRO/2200 PRO - Class I, II, III, IV.
MAX F18 PRO - Class III, IV ONLY.
Gate Type - Vehicular Slide Gate
Max Gate Length - 50 ft
Max Gate Weight:
• MAX 1500 PRO - 1500 lbs Level Gate
• MAX 2200 PRO - 2200 lbs Level Gate
• MAX F18 PRO - 1600 lbs Level Gate
Opening Time - Selectable speed control: ( MAX 1500 PRO/2200 PRO - Up to 12 inch/sec)
( MAX F18 PRO - Up to 18 inch/sec)
Cycles per Hour AC Power - Continuous
Battery Back-Up Cycles (2- 7 Amp/Hr Batteries fully charged) :
• Approximately 100 cycles
Input AC Power/Amps - Switchable: 115VAC / 6 Amp, 1 phase
or 230VAC / 2 Amp, 1 phase
Motor:
• MAX 1500 PRO - 1/2 HP 24VDC Brushless (6 million cycles)
• MAX 2200 PRO/F18 PRO - 1 HP 24VDC Brushless (6 million cycles)
Chain Size - #40
Operating Temperature : -4°F to 158°F (-20°C to 70°C)
Entrapment Protection:
- UL 325 Type A Inherent (ERD sensor)
-
Inputs for NORMALLY CLOSED (N.C.) and 10K Type
UL 325 Type B1 (photocell)
and Type B2 (sensing edge)
29”
14 1/2” 19”
7 1/2”
NOTE: The number of gate cycles using ONLY battery back-up power will vary
depending on the weight of the gate, the gate length, the operating condition
of the gate, temperature and the amount of charge the batteries have at the
beginning of the battery power only operation.
Page
Page
TWO Entrapment protection
sensors MUST be installed,
ONE in EACH direction of
gate travel or operator will
NOT function.
1A
1A
1B
1B
2
3
4
5
6
7
8
9
10
11
12
7
UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7
a