If a self-supporting post is being used, then sensing edges need to be installed on
EACH
side of the post to protect against
entrapment in the
OPENING
and
CLOSING
direction of gate travel.
Self-Supporting Post
Gate Closed
OPENING direction
Sensing Edge
CLOSING direction Sensing Edge
OPENING
direction
Sensing
Edge
Wireless
Module
OPENING
direction
Sensing
Edge
CLOSING direction Sensing Edge
OPENING
direction
Sensing
Edge
(Wireless)
MG
L-T
X20
Mo
nitor
ed
Gat
e Lin
k
Mi
ller
Edg
e
WIRELESS NOTE:
See page 26
OR
Refer to
the instruction sheet that comes with the
wireless module for wiring and mounting
instructions when using wireless option.
W
all
Wireless
Module
Wall
Gate Closed
OPENING direction 10K
NORMALLY CLOSED Sensing Edge
OPENING direction10K NORMALLY CLOSED Sensing Edge Wirelessly
CLOSING direction
10K NORMALLY CLOSED
Sensing Edge Wirelessly
Wireless Module
Wireless
Module
Wireless
Module
Sensing Edges
continued
5
IMPORTANT:
Sensing edges
MUST
be Monitored 10K Type.
Entrapment Protection Device Options and Locations:
The following is a list of recommended accessories for
the MAX Slide PRO Operators.
Omron E3K-R10K4-10R Photocell
EMX IRB-MON Photocell (Thru-Beam)
EMX IRB-RET Photocell (Reflector)
EMX Wireless Edge Link WEL-200T / WEL-200R
Enforcer E931-S50RRGQ Photocell (Reflector)
Enforcer E960-G90GQ Twin Beam (Thru-Beam)
Miller Edge Prime Guard Photocell (Thru-Beam)
Miller Edge GEM-104 10K to NC Converter
Miller Edge R-Band Wireless Edge Unit
P/N: RB-G-RX10 & RB-TX10
Transmitter Solutions IGAZER50LR-UL Photocell (Reflector)
Transmitter Solutions IGAZESR66HD Photocell (Thru-Beam)
Transmitter Solutions Wireless Edge Sensor Model: RCOO900
P/N:
IGAZEREKIT-UL
ASO Edge MAX Mini Edge Contact Edge Sensor
ASO Edge Thin Edge MAX Edge 1 Contact Edge Sensor
Test Connected Sensors
Test
ALL connected
entrapment protection sensors using learn mode:
1.
Press and
HOLD
the
STOP button & then the OPEN
button together until beeping is heard, learn mode begins.
NOTE:
DO NOT
press the
OPEN
button before the
STOP
button or learn mode will
NOT
function.
3.
Press
STOP
button again within 5 min. to end learn mode, beeping stops.
NOTE:
If
STOP
button is not pressed within 5 min. learn mode automatically end after 5 min.
2.
LEDs should be
ON
for each
connected
entrapment sensor detected.
If LEDs are
NOT
on for each connected sensor then they have a problem.
Possible problems:
•
Photocells are out of alignment
•
Photocells are wired wrong - N.C. or N.O. depending on which type
of photocells are used
•
Sensing edges are wired wrong - Not 10K type edge sensor
•
Sensor is bad
MOTION CONTROL
OPEN STOP
CLOSE
MOTION CONTROL
OPEN
STOP
CLOSE
OPEN ONLY
NC
OPEN ONLY
10K
PHOTO CLS
NC
OPEN/CLS
NC
GND
12VDC OUT
GND
CLS ONLY
10K
OPEN/CLS
10K
12VDC OUT
UL SENSOR N.C.
UL SENSOR 10K
P
NSOR N
P
NSOR
P
SOR
P
SOR
SOR
SOR
OR
OR
OR
O
NC
N
N
R
R
R
R
R
R
O
NC
N
N
N
N
R
R
R
R
O
NC
N
N
N
N
N
R
R
R
O
NC
N
N
N
N
N
N
R
R
O
C
N
N
N
N
N
N
N
.C.
N
N
N
N
N
N
N
C.
N
N
N
N
N
C.
.C
.
N.
N
N
N
C
C
.C
.
N
N
UL SEN
UL SEN
UL SEN
UL SE
UL SE
UL SE
UL SE
UL S
L S
O
R1
0K
O
R1
0K
O
R 10K
O
10K
O
10K
10K
10K
10
10
C
ENSOR
R
R
R
R
R
1
1
1
ENSOR
R
R
R
R
R
R
1
1
ENSO
OR
R
R
R
R
R
R
NSO
O
OR
R
R
R
R
R
R
NSO
O
O
OR
R
R
R
R
R
R
NSO
O
O
OR
R
R
R
R
R
NSO
O
O
O
OR
R
R
R
SO
O
O
O
O
OR
R
SO
O
O
O
O
O
NC
NC
Closing Direction
Factory Learned Input
Opening Direction
Factory Learned Input
12VDC OUT monitored
Unlearned Input
Unlearned Input
Opening
Direction
Unlearned Input
Closing
Direction
Unlearned Input
10K Sensing Edges
NC Photocells
8
UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install
Version 7a
Summary of Contents for 1500 PRO
