background image

learn gate positions

7

1.

Push 

OPEN

 button to cycle gate to open position.

Operator cycles slowly while learning position.

2.

Then push 

CLOSE 

button to cycle gate to closed position.

Operator cycles slowly while learning position.

Gate positions have now been learned.

Gate
Shut-Off
Switch

After the virtual limits have been programmed and at least 

ONE

 entrapment sensor has been installed in 

EACH

 direction, 

put the gate in the 

CLOSED

 position:

IMPORTANT:

 

GATE SHUT-OFF

 Switch 

MUST

 be 

OFF

.

(see page 14 for more information about switch)

The 

ERD Sensor

 - 

Electronic Reversing Device 

(Type A) 

MUST

 be adjusted for the 

OPEN and CLOSE gate cycles

.

When the gate encounters an obstruction during the 

CLOSE 

cycle, it will reverse to the open position and

 PAUSE

 the gate.

An input command (press remote button or exit loop) is needed 

BEFORE

 the gate will reset and close again.

When the gate encounters an obstruction during the 

OPEN 

cycle, it will reverse approximately 6 inches and

 PAUSE

 the gate.

An input command (press remote button or exit loop) is needed 

BEFORE

 the gate will reset and open again.

For the 

ERD Sensitivity

 to function correctly:

Gate positions

 must be learned 

BEFORE

 adjusting the ERD Sensitivity. See above.

A.

Turn knob until blue LED lights up.

Maximum sensitivity reached,

Position 1

 - Too sensitive for most gates.

Position 13:

Typical gate setting.

B.

Turn knob 

counter-clockwise

 to

reduce gate sensitivity while testing ERD
until desired results is attained.
(LED remains OFF for all but position 1)

IMPORTANT:

 When satisfied 

with ERD adjustment, cycle 
the gate 3 or 4 times to make 
sure that the ERD sensor does 
not 

falsely trigger

 during 

normal gate operation. 
Re-adjust if this happens.

CAUTION:

 Position 16 results in gate exerting

MAXIMUM force

 before reversing direction.

Adjusting ERD in EACH direction:

Typical Settings:

Position 16:

Heavy gate setting.

Long gate setting.

Cantilever gate setting.

Uphill gate setting.

High wind area gate setting.

Adjust ERD Reverse sensor

8

MOTION CONTROL

OPEN

STOP

CLOSE

MOTION CONTROL

OPEN

STOP

CLOSE

After gate positions have 
been learned, the gate will 
cycle at the speed set on 

“GATE SPEED”

 settings.

16 sensitivity setting positions in EACH direction.

NO mechanical hard stops for knobs.

ERD SENSITIVITY

3

1

14

12

9

7

MAX

SENSE

ERD SENSITIVITY

MIN

16

3

1

14

12

9

7

OPENING

CLOSING

ERD

MOTOR

OVER

LOAD

ERD

MOTOR

OVER

LOAD

MAX

SENSE

MAX

SENSE

ERD SENSITIVITY

MIN

3

1

14

16

MIN

16

12

9

7

3

1

14

12

9

7

MAX

SENSE

ERD SENSITIVITY

MIN

16

3

1

14

12

9

7

MAX

SENSE

ERD SENSITIVITY

MIN

16

3

1

14

12

9

7

If alarm sounds while adjusting ERD, 
press 

STOP BUTTON

 to shut-off alarm.

MOTION CONTROL

OPEN

STOP

CLOSE

Typically set to MAX, LEDs ON.

CLOSING

OPENING

GATE SPEED

MIN

MIN

MIN

MIN

MIN

MI

M

M

MIN

MIN

MIN

MI

M

M

MAX

MAX

1

MAX

SENSE

16

MIN

CAUTION: Keep pedestrians and vehicles clear of the gate while adjusting sensors.

10

UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install 

Version 7a

Summary of Contents for 1500 PRO









































Reviews: