background image

CLOSING Photocell Beam

OPENING Photocell Beam

Reflector

CLOSING
Sensing
Edge with
Wireless
Module

Operator Placement (standard)

1A

V-Rail

Physical Stop

Concrete Pad

Operator

Position on

Concrete Pad

Operator in Front Position (Standard)

Operator in Front Position (Standard)

Outside Property

Inside Property

24”

24”

Wireless

Module

Gate in Closed Position

4”

4”

2” Gate Frame

10.5”

10.5”

6.2”

6.75”

7.5”

7.5”

6.75”

Cover

1.5”

4”

5”

6.5”

The gate must be properly installed and work freely in both directions prior to installation of the gate operator.

REQUIRED - 

AC input power wire.

REQUIRED - 

Entrapment protection 

OPENING

 and 

CLOSING

 photocell 

and/or sensing edges.

In-ground loop wires.

Conduit Guidelines and Suggestions

8.625”

12.75”

Conduit

Area

Input Power

Conduit Run

Concrete Pad

Check local building 
codes in your area for 
depth of concrete 
before installation.

Guide rollers 

MUST

 be Installed to keep gate upright.

6” above ground to avoid flooding.

Concrete Depth Note:

 The heavier the gate, the deeper the concrete pad should be. At least 

two feet

 recommended for heavier gate.

Secure gate operator to 

concrete pad with four 

(4) 1/2” x 3” (min) 

sleeve anchors.

1/2

Wireless

Module

CLOSING
Sensing
Edge with
Wireless
Module

Guide Rollers

Safety sensors (Photocell or contact EDGE) must be 
installed in 

BOTH

 opening and closing direction of gate 

movement where entrapment or pinch point exist. 

TWO

 

safety sensor min. (N.C. or 10K type) 

MUST

 be installed or 

operator will 

NOT

 function. 

All

 sensors must be UL325, 

2018 compliant. See pages 7-8.

UL 325 2018 Standard

IMPORTANT:

 Physical stops 

MUST

 

be installed on 

BOTH

 ends of rail to 

keep gate from traveling off of rail.

IMPORTANT:

Physical Stop

MUST

 be installed

See next page for chain information.

Choose either      Front Mounting Position (Standard) or      Rear Mounting Position (Alternate).

1A

1B

OPENING Sensing Edge with Wireless Module

OPENING Sensing Edge with Wireless Module

Operator MUST be level.

step-by-step installation

1

UL 325 2018 Standard - MAX 1500 PRO/2200 PRO/F18 PRO Matrix III Install Version 7

a

Summary of Contents for 1500 PRO









































Reviews: