Manitou MSI 40 T S3 ST3B, Operator'S Manual

Page: 74 / 114

3-8
SERVICING SCHEDULE
IMPORTANT
(1): COMPULSORY 500 HOURS OR 6 MONTH SERVICE. This service must be carried out after approximately the first 500 hours of operation or within the 6 months following
the start-up of the machine (whichever occurs first).
(2): Consult your dealer.
A = ADJUST, C = CHECK, G = GREASE, N = CLEAN, P = BLEED,
R = REPLACE, V = DRAIN
PAGE (1)
D
AIL
Y OR E
VER
Y 10
HOURS OF SER
VICE
EVER
Y 50 HOURS OF
SER
VICE
EVER
Y 250 HOURS
OF SER
VICE
EVER
Y 500 HOURS
OF SER
VICE OR
EVER
Y Y
EAR
EVER
Y 1000 HOURS
OF SER
VICE OR
EVER
Y T
W
O Y
EARS
EVER
Y 2000 HOURS
OF SER
VICE OR
EVER
Y T
W
O Y
EARS
EVER
Y 3000 HOURS
OF SER
VICE
EVER
Y 4000 HOURS
OF SER
VICE
OC
CASIONALL
Y
I.C. ENGINE
-I.C. engine oil level 3-10 C C
-Cooling liquid level 3-10 C C
-Fuel level 3-10 C C
-Fuel pre-filter 3-11 C C
-Cyclonic pre-filter (option) 3-11 N N
-Dry air filter cartridge 3-12/22 C/N C/N R
-Radiator core 3-12 N N
-Engine compartment 3-13 N N
-Condenser core (OPTION Air conditioning) 3-13 C C
-Compressor belt tension (OPTION Air conditioning) 3-18 C/A C/A
-I.C. engine oil 3-22 V V
-I.C. engine oil filter 3-22 R R
-Fuel pre-filter cartridge 3-23 R R
-Fuel filter cartridge 3-24 R R
-Engine crankcase ventilation filter 3-26 R
-Fuel tank 3-26 N
-Fuel tank breather 3-26 R
-Safety dry air filter cartridge 3-27 R
-I.C. engine silent blocks C (2)
-I.C. engine rates C (2)
-Valves clearances C C (2)
-Cooling liquid 3-30 V
-Radiator C (2)
-Water pump and the thermostat C (2)
-Alternator and the starter motor C (2)
-Turbocompressor C (2)
-Alternator belt R (2)
-Fuel circuit 3-32 P
-Regenerating the “stationary lift truck” exhaust particle filter 3-32 XXX
TRANSMISSION
-Hydrostatic transmission circuit pressures C (2)
-Governing start of the hydrostatic transmission C (2)
-Wear of the brake pads and the brake disk C (2)
TYRES
-Tyres pressure 3-13 C C
-Wheel nuts torque 3-13 C C
-Wheel nuts tightening torque 3-30 C C
-Wheel 3-33 R
MAST
-Tension and alignment of the mast lifting chains 3-13 C/A C/A
-Mast 3-14 G G
-Mast lifting chains 3-24 N/C/G N/C/G C (2)
-Condition of mast unit C (2)
-Chain rollers C (2)
-Mast guide rollers C (2)
-Mast bearing rollers C (2)
-Thickness of the mast wearing plates C (2)
647177 (23/02/2017) MSI 40/50 T S3 ST3B