Manitou MLT625-75 H S1-E3, Operator'S Manual

Page: 38 / 160

1-14 1-14
500 mm 500 mm
B2 B2
1 1
2 2
3 3
C C
- - For irregular loads, determine the tr For irregular loads, determine the tr ansverse centre of gravity ansverse centre of gravity before any movement ( before any movement ( fig. fig.
B2) and set it in the longitudinal axis of the lift tr B2) and set it in the longitudinal axis of the lift tr uck. uck.
It is forbidden to move a It is forbidden to move a load heavier than the effective capacity defined on the load heavier than the effective capacity defined on the lift truck load chart. lift truck load chart.
For loads with a moving centre of gravity (e.g. liquids), take account of the variations in the centre of For loads with a moving centre of gravity (e.g. liquids), take account of the variations in the centre of
gravity in order to gravity in order to determine the load to be handled and be determine the load to be handled and be vigilant and take extra care to vigilant and take extra care to limit these limit these
variations as far as possible. variations as far as possible.
C - LONGITUDINAL C - LONGITUDINAL ST ST ABILITY LIMITER AND WARNING DEVICE ABILITY LIMITER AND WARNING DEVICE
This device gives an indication of the longitudinal stability of the lift truck, and limits This device gives an indication of the longitudinal stability of the lift truck, and limits
hydraulic movements in order to ensure hydraulic movements in order to ensure this stability this stability , at least under , at least under the following operating the following operating
conditions: conditions:
• • when the lif when the lif t truck is at t truck is at a standstill, a standstill,
• • when the lift truck is on when the lift truck is on firm, stable and conso firm, stable and conso lidated ground, lidated ground,
• • when the lif when the lif t truck is performing handling and pl t truck is performing handling and pl acing operations. acing operations.
- - Move the jib very carefully when approaching the authorized load limi Move the jib very carefully when approaching the authorized load limi t (see: 2 - DESCRIPTION: t (see: 2 - DESCRIPTION:
INSTRUMENTS AND CONTROLS). INSTRUMENTS AND CONTROLS).
- - Always watch this Always watch this device during handli device during handli ng operations. ng operations.
- - In the event that "AGGRA In the event that "AGGRA VA VA TING" hydraulic movem TING" hydraulic movem ents are cut-off, only per ents are cut-off, only per form form
de-aggravating hydraulic movements in the following order (fig. C): if necessar de-aggravating hydraulic movements in the following order (fig. C): if necessar y, raise the y, raise the
jib (1), retract the ji jib (1), retract the ji b as far as poss b as far as poss ible (2) and lower ible (2) and lower the jib (3) to s the jib (3) to s et down the load. et down the load.
The instrument reading may be erroneous when the steering is at its maximum limit or the rear axle The instrument reading may be erroneous when the steering is at its maximum limit or the rear axle
oscillated to its limit. Before lifting a load, make sure that the lift truck is not in either of these oscillated to its limit. Before lifting a load, make sure that the lift truck is not in either of these
situations. situations.
D - TRANSVERSE ATTITUDE OF THE LIFT TRUCK D - TRANSVERSE ATTITUDE OF THE LIFT TRUCK
Depending on the model of lift truck Depending on the model of lift truck
The transverse attitude is the transverse slope of the chassis with respect to the The transverse attitude is the transverse slope of the chassis with respect to the
horizontal. horizontal.
Raising the jib reduces the Raising the jib reduces the lift truck’s lateral stability. The transverse attitude must be set lift truck’s lateral stability. The transverse attitude must be set
with the jib in down position as follows: with the jib in down position as follows:
1 - LIFT 1 - LIFT TRUCK WITHOUT SLOPE CORRECTOR USED ON TYRES TRUCK WITHOUT SLOPE CORRECTOR USED ON TYRES
- - Position the lift truck so that the bubbl Position the lift truck so that the bubbl e in the level is between the two li e in the level is between the two li nes (see: 2 - nes (see: 2 -
DESCRIPTION: INSTRUMENTS AND CONTROLS). DESCRIPTION: INSTRUMENTS AND CONTROLS).
2 - LIFT 2 - LIFT TRUCK WITH SLOPE CORRECTOR USED ON TYRES TRUCK WITH SLOPE CORRECTOR USED ON TYRES
- - Correct the slope using the hydraulic Correct the slope using the hydraulic control and verify the horizon control and verify the horizon tality via the level. Th tality via the level. Th e e
bubble in the level must be between the two bubble in the level must be between the two lines (see: 2 - DESCRIPTION: INSTRUMENTS lines (see: 2 - DESCRIPTION: INSTRUMENTS
AND CONTROLS). AND CONTROLS).
D1 D1
D2 D2
https://www.forkliftpdfmanuals.com/