Manitou MLA 628 -120 LSU 3-E2 Series, Operator'S Manual

Page: 93 / 130

3 - 13 3 - 13
AND FUEL) by the filler port 3 (fig. A5/1). AND FUEL) by the filler port 3 (fig. A5/1).
NOTE NOTE : COLD LEVEL (b : COLD LEVEL (betwe etween 59°F and 68° en 59°F and 68°F) F)
The oil must be at its minimum, The oil must be at its minimum, at the level of the sc at the level of the screw 1 (fig. A5/1) rew 1 (fig. A5/1)
HOT LEVEL (between 180°F and 200°F) HOT LEVEL (between 180°F and 200°F)
The oil must be at the level of the screw 4 (fig. A5/1).
The oil must be at the level of the screw 4 (fig. A5/1).
A6 - T A6 - T
IIR RE ES S PR PRE ES SS SUR URE E A AN ND D W WH HE EE EL L NU NUTS TS T TO ORQ RQU UE E
CHECK CHECK
- Chec - Check the cond k the condition of t ition of the tires he tires,, to detec to detect cuts, t cuts, wear wear,, etc. etc.
- Check the torque load of the wheel nuts. Non compliance with this instruction can cause damage and rupture to the wheel - Check the torque load of the wheel nuts. Non compliance with this instruction can cause damage and rupture to the wheel bolts bolts
and distortion to the wheels. and distortion to the wheels.
Wheel nuts tightening torque Wheel nuts tightening torque
• Fro • Front tires nt tires : 465 ft/ : 465 ft/lb lb
• Rear • Rear tires tires : 465 ft : 465 ft/lb /lb
- Check and adjust the tire pressures if necessary (see : 2 - DESCRIPTION - Check and adjust the tire pressures if necessary (see : 2 - DESCRIPTION : CHARACTERISTICS : CHARACTERISTICS). ).
Check that the air hose is correctly connected to the tire valve before inflating and keep all persons at a distance during inflation. Respect Check that the air hose is correctly connected to the tire valve before inflating and keep all persons at a distance during inflation. Respect
the recommended tire pressures given. the recommended tire pressures given.
A5/2 A5/2
4 4
1 1
2 2
Check that the air hose is correctly connected to the tire valve before inflating and keep all persons at a distance dur- Check that the air hose is correctly connected to the tire valve before inflating and keep all persons at a distance dur-
ing inflation. Respect the recommended tire pressures given.
ing inflation. Respect the recommended tire pressures given.
WARNING WARNING
A7 - B A7 - B
OO OOM M P PA AD DS S
CLEAN - GREASE CLEAN - GREASE
T To be carried out every 10 hours during the first 50 hours service, o be carried out every 10 hours during the first 50 hours service, then once at 250 hours. then once at 250 hours.
- Extend the - Extend the boom completely. boom completely.
- With a - With a brush, brush, apply a coat apply a coat of grease of grease (see : 3 (see : 3 - MAINTENANCE - MAINTENANCE : LUBRICANTS : LUBRICANTS AND FUEL) AND FUEL)
on the 4 sides of the telescope(s) (fig. A7). on the 4 sides of the telescope(s) (fig. A7).
- Teles - Telescope the boom cope the boom several times in several times in order to spread the order to spread the coat of grease evenly. coat of grease evenly.
- Remove the surplus of grease. - Remove the surplus of grease.
If the lift truck is used in an abrasive environment (dust, sand, coal…) Use lubricating varnish If the lift truck is used in an abrasive environment (dust, sand, coal…) Use lubricating varnish
(MANI (MANI TOU ref TOU ref erence erence : 483536). In this : 483536). In this respect, consult your dealer. respect, consult your dealer.
A7 A7
If the lift truck is used in an abrasive environment (dust, sand, coal…) Use If the lift truck is used in an abrasive environment (dust, sand, coal…) Use
lubricating varnish, contact your dealer.
lubricating varnish, contact your dealer.
IMPORTANT IMPORTANT
CONTENTS CONTENTS
https://www.forkliftpdfmanuals.com/