Magnum Energy ME-AGS-N Owner'S Manual Download

Page: 91 / 103

11.0 ME-AGS-N Remote Status Messages

Table 11-1, AGS Remote Operational Statuses (cont.)

STATUS

REMOTE

DESCRIPTION

Gen

Warm-up

ARC/RTR

The AGS is attempting to start the generator and

a time period has been set under the

SETUP: 04I

Gen Warm-up Time

setting. Once the AGS sta-

tus indicates

Warm-up

, the inverter/chargers

AC input ignores any incoming AC power. This

prevents the inverter/charger from loading the
generator during warm-up. Once the AGS has

determined that the generator is running, the
warm-up time setting must be met before the
generator can connect to the inverter/charger.

Manual

Run

The generator was started manually from a start/

stop switch directly connected to the generator,
and the

AGS Mode

is set to

Other

(if the

AGS

Mode=RV

, a Lockout fault displays instead).

ARC/RTR

The generator was started manually from a start/

stop switch directly connected to the generator,
or from the

CTRL: 03 Gen Control

menu.

Note:

The AGS determines that the generator has been manually turned

on by sensing a gen run sense voltage to Terminal #2 on the AGSs 8-port

terminal block. However, if the Gen Type DIP switch is set to 2-Wire
Standby which does not require a gen run sense voltage manually

turning the generator on displays a status of

AC In

rather than

Manual

Run

Quiet

Time

The ME-AGS-N has entered Quiet Time per the

AGS: 07 Quiet Time setting.

ARC/RTR

The AGS has entered Quiet Time per the

SETUP:

04G Quiet Time

setting.

Note:

The generator will not autostart during Quiet Time.

Lockout

Lockout occurs when the AGS system is automat-

ically disabled because the generator has been
started or stopped for any condition outside the

control of the AGS. This an RVIA requirement,
refer to the information on the AGS mode under

the

AGS: 08 AGS TECH

menu on page 35.

Note:

When a Lockout status occurs, the

AGS: 01 AGS Control

menu au-

tomatically changes from

Enable

(or

Enable w/QT

) to

Off

For assistance in clearing or disabling this status, refer to Section 12.2

Resolving Operational Statuses.

Note:

In installations where the requirement to automatically disable the

AGS system is not needed, the AGS mode can be changed to

Other

Refer to the information on the AGS mode under the

AGS: 08 AGS TECH

menu on page 35.

Summary of Contents for ME-AGS-N








































































































Search results

Summary of Contents for ME-AGS-N

Reviews:

Related manuals for ME-AGS-N

Brands by name

Popular brands

Magnum Energy ME-AGS-N, Owner'S Manual

Search results

Summary of Contents for ME-AGS-N

Reviews:

Related manuals for ME-AGS-N

Brands by name

Popular brands