Mada Sigma Series Operation Manual Download

Page: 6 / 56

SIGMA LASER STENT AND TUBE CUTTER

990-401

Before

using this equipment, read the

Safety Precautions

carefully to understand the correct usage of the

equipment.



These precautions are given for the safe use
of the Tube Cutter and for prevention of
injury to operators or others.



Be sure to read

each

of the instructions, as

they are all important for safe operation.



The meaning of the words and symbols are
as follows:

DANGER

not

touch the interior of the Tube Cutter when it is turned ON.

Doing so may result in electric shock.

Never

attempt to disassemble, repair, or modify the Tube Cutter.

Doing so may result in electric shock or fire.
Refrain from any mechanical adjustment other than the maintenance procedures specifically
described in the operation manual.

Summary of Contents for Sigma Series

























































Search results

Summary of Contents for Sigma Series

Reviews:

Related manuals for Sigma Series

Brands by name

Popular brands

Mada Sigma Series, Operation Manual

Search results

Summary of Contents for Sigma Series

Reviews:

Related manuals for Sigma Series

Brands by name

Popular brands