background image

PRODUCT WARRANTY

Luxtec warrants that the CLX light source (except the lamp) shall be free from defects 
in material and workmanship under normal use and service for a period of three (3) 
years from the date of shipment from Luxtec. Luxtec’s sole and exclusive liability under 
the warranty shall be, at Luxtec’s option, either to repair or to replace any component 
which fails during the warranty period due to any defect in workmanship or material 
F.O.B. factory if:

1. Customer promptly reports such defect to Luxtec in writing,
2. If requested by Luxtec, customer returns equipment to Luxtec at the customer

expense and,

3. Upon inspection, Luxtec finds the equipment to be defective.

This warranty is contingent upon normal and proper use of the equipment. It does not 
cover equipment modified without the written approval of Luxtec, subjected to unusual 
physical or electrical stress, altered with non-Luxtec parts or damaged during shipment 
back to Luxtec. This warranty is non-transferable unless authorized in writing by 
Luxtec.

Luxtec reserves the right to make design changes on its products without liability to 
incorporate said change in Luxtec products previously designed or sold.
Upon receipt of the product, it should be carefully inspected. If any defect is 
discovered, Luxtec must be notified immediately.

REPAIR AND RETURN

This device must be clean of all blood or other organic material prior to returning 
to Luxtec. Luxtec reserves the right to return unrepaired any equipment that is 
contaminated with blood or other organic material.

Warranty Service and Repair:

To obtain service under warranty or return product for repair, the customer 
should contact your local Luxtec distributor or call Luxtec Customer Service at 
(800)325-8966 (US only) or +1-508-835-9700.

Information contained in this manual is subject to change without notice.

- 15 -

Summary of Contents for 00-CLX


















Reviews: