background image

 

 

   

 

 

Operating Manual 

Cross-flow fan unit  type GSG-NV1 / 2

 

 

   

 

 

 

43 - 64 

 010980-26-E BA GSG-NV1_2 / 23.03.2012

 

 

 

 

 

 

 

 

21. Interruption of spraying process 

 

If the spraying process will be interrupted e.g. due to weather condi-
tions, all parts which were in contact with spraying agent like pump, 
spraying pipes, fittings and filters should be cleaned on the spraying 
ground. 
 
Normally a length of the run of 20 m is sufficient. 
 
This cleaning avoids blockage of filters and nozzles. 

 

 

 
 
 
 
 
 
 
 
 
 

 

 

 
 

 

 

Abb. 30a 

 Abb. 30b 

 

 

Set  the  3-way  valve  (1) 

to  the  middle  position  “Clean  suction 

fil

ter” (Fig. 30a). This will shut-off the agent spraying circuit. 

 

 

Set both 2-way valves (2+3) 

to position “Machine cleaning” (Fig. 

30a/b). The pump will bring fresh water from fresh water tank to 
the spraying nozzles. 

 

 

Shut-off Recycling procedure on control box. 

 

 

This will avoid, that cleaning liquid will be pumped through recy-
cling injectors back to the spray liquid tank, thus thinning the liq-
uid in the spray liquid tank. 

 

 

Switch on pump, water from fresh water tank is now cleaning all 
fittings,  filters  close  to  the  spraying  nozzles  and  the  nozzles 
themselves. 

 

 

The cleaning liquid must be disposed on agricultural / forested / 
horticultural surface.

 

 

Summary of Contents for GSG-NV Series

































































Reviews: