Lionel ES44AC Owner'S Manual Download Page 28 | Manualshive

Page: 28 / 36

background image

28

Reprogramming your locomotive to restore features (LEGACY)

Maintaining and servicing your locomotive

I

f your locomotive is unresponsive to your commands in the Command Control environment, we
recommend that you follow this procedure to reset your locomotive. All factory default settings will

be restored when you reprogram the locomotive.

1. Slide the Program-Run switch to the PGM position.
2. Plug in and connect your LEGACY Base.
3. Place your locomotive on the track, then power up the track.
4. Press ENG and enter the locomotive’s ID#.
5. Press SET.
6. Slide the Program-Run switch back to the RUN position.

At this point, your locomotive has been reset. Restore power to the track and operate the locomotive
as usual. Be sure to use the ID# entered in Step 4.

«
...
26
27
28
29
30
...
»

Summary of Contents for ES44AC





































Reviews:

No comments

Related manuals for ES44AC

Brand: MADRIX Pages: 12

Brand: Narcotrend Pages: 47

Brand: Water Witch Pages: 2

Brand: Falltech Pages: 48

Lab companion SI-300

Brand: Jeio tech Pages: 69

IP Video Test Option HST-3000

Brand: JDS Uniphase Pages: 4

Brand: Jct Pages: 16

Brand: Ganter Norm Pages: 20

Chandler Engineering 1910

Brand: Ametek Pages: 46

Brand: ORORO Pages: 16

Brand: Honestech Pages: 43

A/C Air Launcher 101050

Brand: CITC Pages: 10

Brand: Becker-Elektronik Pages: 24

Brand: Augmedics Pages: 31

Brand: EuroLite Pages: 36

Brand: W&H Pages: 46

Brand: Vega Industries Pages: 53

Brand: Weider Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands