Lionel ES44AC Owner'S Manual Download Page 29 | Manualshive

Page: 29 / 36

background image

29

Reprogramming your locomotive to restore features (TMCC)

Maintaining and servicing your locomotive

I

f your locomotive is unresponsive to your commands in the Command Control environment, we
recommend that you follow this procedure to reset your locomotive. All factory default settings will

be restored when you reprogram the locomotive.

1. Slide the Program-Run switch to the PGM position.
2. Plug in and connect your Command Base.
3. Place your locomotive on the track, then power up the track.
4. Press ENG and enter the locomotive’s ID#.
5. Press SET.
6. Slide the Program-Run switch back to the RUN position.

At this point, your locomotive has been reset. Restore power to the track and operate the locomotive
as usual. Be sure to use the ID# entered in Step 4.

«
...
27
28
29
30
31
...
»

Summary of Contents for ES44AC





































Reviews:

No comments

Related manuals for ES44AC

Brand: Kapriol Pages: 32

ImageQuant LAS 4000

Brand: GE Pages: 86

Brand: GE Pages: 160

Brand: GE Pages: 134

Brand: Oberheim Pages: 40

Brand: Ecco Pages: 2

Brand: Landoll Pages: 94

Brand: xsto Pages: 76

Brand: F&V Pages: 5

Brand: F Care Systems Pages: 2

Brand: Major Pages: 52

Brand: HABYS Pages: 16

Brand: PASCO Pages: 30

Brand: M-Audio Pages: 48

Brand: M-Audio Pages: 19

Brand: M-Audio Pages: 17

Brand: M-Audio Pages: 18

Brand: M-Audio Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands