Lionel ES44AC Owner'S Manual Download | Manualshive

Page: 2 / 36

background image

2

Thank You!

T

hank you for your purchase of this American Flyer LEGACY diesel locomotive! On the outside,
this locomotive features numerous details and expert decoration in your favorite livery. Inside

the body, this locomotive is equipped with some of the most advanced sounds and controls in model
railroading. This powerful locomotive is ready for duty on your layout.

This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including interference that may cause undesired operation.
Contains
P/N: WJ-M101L
FCC ID: LIV-BLEMOD1
IC: 7032A-BLEMOD1

FCC Statement

LEGACY® Control System

This revolutionary control system allows you to run your LEGACY® Control System-
equipped locomotive just like a real engineer runs his trains. With its enhanced sounds
and 200 speed steps, this system allows properly equipped engines to function with
unparalleled options. The CAB-2 Remote Controller has an LCD screen display, vibration
that simulates the effort of the locomotive, and other exciting operating features. The
new CAB-IL Remote Controller is a simplified alternative to unlock many LEGACY®
features.

LEGACY® RailSounds®

Widely regarded as the industry standard, the impressive RailSounds® sound system
brings the real sounds of the railroad to your layout. From the mechanical symphony of
the locomotives, to the commotion of the station, you will be impressed by the digitally
recorded samples of these special and authentic sounds.

The following Lionel marks are used throughout this Owner’s Manual and are protected under law. All
rights reserved.
Lionel®, LionChief®, LionChief Plus®, FlyerChief®, TMCC

®

, LEGACY

®

, FasTrack®, TrainMaster®,

Odyssey®, RailSounds®, CrewTalk™, TowerCom™, ElectroCoupler™, CAB-1® Remote Controller,
TMCC®, Wireless Tether™, SensorTrack™, DynaChuff™, MultiWhistle™

DCC On Board is a Registered Trademark of Bachmann Industries, Inc. All Rights Reserved.
Digitrax is a Registered Trademark of Digitrax, Inc. All Rights Reserved.

«
1
2
3
4
...
»

Summary of Contents for ES44AC





































Reviews:

No comments

Related manuals for ES44AC

Brand: Oberheim Pages: 40

Brand: Tascam Pages: 80

Brand: Tascam Pages: 2

Brand: Walker Pages: 24

Brand: Garmin Pages: 2

Brand: Qu-Bit Electronix Pages: 15

Brand: Teac Pages: 44

Brand: Te Pari Pages: 6

Brand: UNI-T Pages: 4

UPO3000E Series

Brand: UNI-T Pages: 94

Brand: UMS Pages: 92

Brand: Waters Pages: 250

Brand: Waters Pages: 141

WELCH LVS 600 T

Brand: Gardner Denver Pages: 68

Avisa Line XL04

Brand: FHF Pages: 2

Brand: Joerns Healthcare Pages: 106

Brand: Eleiko Pages: 4

Brand: Heiniger Pages: 164

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands