Limitorque LY 1001 Series Installation And Maintenance Manual Download Page 50

Page: 50 / 63

7-8

LY Installation and Maintenance for LY 1001, LY 2001 and LY 3001

LMAIM1501

Install Handwheel Assembly

12. Install the Clutch Sleeve (piece #13), ensuring the Declutch Fork Assembly (piece #46) is between the Input

Worm Gear (piece #18) and the Clutch Sleeve (piece #13).

13. Install Thrust Washer (piece #26), Thrust Bearing (piece #27) and second Thrust Washer (piece #26) into the

Handwheel Clutch (piece #16).

14. Put a light coat of grease on the Thrust Bearing. Install Spring (piece #17) into the Handwheel Clutch.

15. Install Handwheel Clutch Assembly (pieces #16, 17, 26 [2 pcs], and 27) into the Housing. Push remaining

Worm Shaft Assembly into the Handwheel Clutch of the Handwheel Clutch Assembly.

16. Install O-Ring (piece #135) over the Worm Shaft Assembly Bearing.

17. Install Bearing Cap (piece #5) and Hardware (pieces #61 and 62).

LY 2001 Handwheel Assembly

18. Install Handwheel Assembly (pieces #146, 41, 112, 69, 192, 134, and 37).

19. Install Hardware (pieces #70 and 71).

20. Go to Step 22.

LY 3001 Handwheel Assembly

18. Install the Handwheel Gear Assembly (pieces #119, 35, and 37).

19. Install the Handwheel Pinion and Idler (piece #43) and Idler Shaft (piece #42).

20. Install the Handwheel Assembly (pieces #146, 41, 112, 136, 39, 34, 137, 116, 115, 38, and 36).

21. Install Screws (pieces #63 and 65) and Lockwashers (pieces #64 and 66) to secure the Handwheel Assembly

onto the housing.

Install Input Worm Motor Pinion Assembly

22. Install Input Worm Motor Pinion Assembly (piece #52, 53, 124, and 31) into the Housing.

23. Install Housing Seal (O-Ring) (piece #131).

Grease Unit

24. Grease unit with the properly recommended grease. (See Section 7.1, Lubrication.)

Install Top Plate

25. Install Top Plate (piece #2) and Hardware (piece #88 and 89).

NOTE: If Top Plate will not fit properly, check Bearing (piece #33) and Declutch Shaft (piece #44) for proper

alignment into Top Plate molding.

Install Torque Switch Assembly, Motor Assembly, and Limit Assembly

26. Install Torque Switch Assembly with Gasket (piece #8) and Hardware (piece #97 and 98).

27. Install Limit Switch (piece #7) with Hardware (piece #79 and 80).

28. Reconnect Limit Switch, Torque Switch, and Terminal Strip. Refer to the actuator wiring diagram for proper

wiring configuration.

Install Control Cover

NOTE: Before installing the Control Cover, reset the Limit Switches and Mechanical Stops. Recheck motor for

proper rotation.

29. Install Cover O-Ring (piece #130).

30. Install Control Cover (piece #3) with Hardware (piece #67 and 68).

Flow Control Division

Limitorque Actuation Systems

Summary of Contents for LY 1001 Series
































































Search results

Summary of Contents for LY 1001 Series

Reviews:

Related manuals for LY 1001 Series

Brands by name

Popular brands

Limitorque LY 1001 Series, Installation And Maintenance Manual

Search results

Summary of Contents for LY 1001 Series

Reviews:

Related manuals for LY 1001 Series

Brands by name

Popular brands