manualshive.com logo in svg

Limitorque LY 1001 Series, Installation And Maintenance Manual, Page: 46 / 63

Share
Download
Limitorque LY 1001 Series Installation And Maintenance Manual Download Page 46

7-4

LY Installation and Maintenance for LY 1001, LY 2001 and LY 3001

LMAIM1501

Figure 7.1 – LY 1001 Declutch Return Spring Installation Position

4. 

Install Declutch Assembly (piece #46, 123, 44, and 55).

5. 

Install O-Ring (piece #138) over Declutch Shaft (piece #44).

6. 

Install Declutch Lever (piece #45) and Roll Pin (piece #121).

Install Drive Sleeve

7. 

Install Drive Sleeve (piece #10).

8. 

Install Ball Bearing (piece #33) and O-Ring (piece #129) on the Drive Sleeve.

Install Worm Shaft Assembly

9. 

Install Worm Shaft Assembly.

NOTE: Push the Worm Shaft Assembly through to about 1/2" past the Input Worm Gear for installing the

Clutch Sleeve (piece #13).

Install Handwheel Assembly

10. Install the Clutch Sleeve (piece #13), ensuring the Declutch Fork Assembly (piece #46) is between the Input

Worm Gear (piece #18) and the Clutch Sleeve (piece #13).

11.  Install Thrust Washer (piece #26), Thrust Bearing (piece #27), and second Thrust Washer (piece #26) into the

Handwheel Clutch (piece #16).

12.  Put a light coat of grease on the Thrust Bearing. Install Spring (piece #154) into the Handwheel Clutch.

13. Install Handwheel Clutch Assembly (pieces #16, 154, 26 [2 pcs], and 27) into the Housing. Push remaining

Worm Shaft Assembly into the Handwheel Clutch of the Handwheel Clutch Assembly.

14.  Install O-Ring (piece #135) over the Worm Shaft Assembly Bearing.

15.  Install Disc Spring Cap (piece #5) and Hardware (pieces #61 and 62).

16. Install Handwheel Cap Gasket (piece #137) and Handwheel Assembly (pieces #41, 112, 34, 137, 134, 155 

[2 pcs], 154, 70, and 37).

17. Install Hex Head Cap Screw and Lockwasher (pieces #63 and 64).

6301 .

6301 .

Rib

Bottom
Declutch
Fork

LY 1001 End View

#47 Declutch
Return Spring

Rib

LY 1001 Top View

Flow Control Division

Limitorque Actuation Systems

Summary of Contents for LY 1001 Series
































































Reviews:

No comments