Limitorque LY 1001 Series Installation And Maintenance Manual Download Page 47

Page: 47 / 63

LMAIM1501

LY Installation and Maintenance for LY 1001, LY 2001 and LY 3001

7-5

Install Input Worm Motor Pinion Assembly

18. Install Input Worm Motor Pinion Assembly (pieces #52, 156, 53, 124, and 31) into the Housing.

19. Install Housing Seal (O-Ring) (pieces #131).

Grease Unit

20. Grease unit with the properly recommended grease. (See Section 7.1, Lubrication.)

Install Top Plate

21. Install Top Plate (piece #2) and Hardware (pieces #65 and 66).

NOTE: If Top Plate will not fit properly, check Ball Bearing (piece #33) and Declutch Shaft (piece #44) for

proper alignment into Top Plate molding.

Install Torque Switch Assembly, Motor Assembly, and Limit Assembly

22. Install Torque Switch Assembly (piece #8) with Gasket and Hardware (piece #98 and 97).

23. Install Limit Switch Assembly (piece #7) and Heater Assembly (piece #120) with Hardware (piece #77, 78, 79,

and 80).

24. Reconnect Limit Switch, Torque Switch, and Terminal Strip. (See the wiring diagram included with the actuator

for proper wiring configuration.)

Install Control Cover

NOTE: Before installing the Control Cover, reset the Limit Switches and Mechanical Stops. Recheck motor for

proper rotation.

25. Install Cover Seal O-Ring (piece #130).

26. Install Control Cover (piece #3) with Hardware (piece #67 and 68).

7.3.3

LY 2001/3001 Disassembly

DANGER: HAZARDOUS VOLTAGE. Turn off all power before disassembling your LY actuator.

DANGER: POTENTIAL HIGH-PRESSURE VESSEL. Before disassembling your actuator, ensure that the valve or

other actuated device is isolated and is not under pressure.

Piece numbers refer to Figures 6.8, 6.9, 6.10, and 6.11.

Remove Cover and Top Plate

Shut off all power to the actuator.

Remove the Control Cover (piece #3).

Disconnect all electrical leads from the Torque Switch (piece #8) and Limit Switch (piece #7). Make sure all

wire leads are properly marked for reassembly.

Remove all external wires to the Terminal Strips (piece #9, 110, and 111).

If unit has an Integral Assembly, remove all wires from the Integral Assembly to the Terminal Strip (piece #9,

110, and 111).

Remove Screws/Lockwashers (piece #79 and 80) that are holding the Limit Switch (piece #7). Remove the

Limit Switch.

Remove two Screws (piece #97) and two Lockwashers (piece #98) that are holding the Torque Switch (piece

#8). Remove the Torque Switch.

Remove two Screws (piece #88) and two Lockwashers (piece #89) to remove the Top Plate (piece #2).

Lift Top Plate (piece #2) off the LY Housing (piece #1). The Motor (piece #6) can be left attached to the Top

Plate when the Top Plate is removed.

Flow Control Division

Limitorque Actuation Systems

Summary of Contents for LY 1001 Series
































































Search results

Summary of Contents for LY 1001 Series

Reviews:

Related manuals for LY 1001 Series

Brands by name

Popular brands

Limitorque LY 1001 Series, Installation And Maintenance Manual

Search results

Summary of Contents for LY 1001 Series

Reviews:

Related manuals for LY 1001 Series

Brands by name

Popular brands