Limitorque LY 1001 Series Installation And Maintenance Manual Download Page 32 | Manualshive

Page: 32 / 63

background image

6-4

LY Installation and Maintenance for LY 1001, LY 2001 and LY 3001

LMAIM1501

6.2.2

Single-Phase Motor

NOTE: Your application may vary from the standard wiring configuration for the single-phase motor shown in

Figures 6.3 and 6.4. Refer to the specific actuator wiring diagram for wiring configuration.

1.

Using the Handwheel, move the valve to a midtravel position. Midtravel position allows electrical operation in

the valve “safe” area and keeps the OPEN and CLOSED limit switches from tripping while testing motor

direction.

2.

Momentarily press the OPEN pushbutton to test motor direction. If the actuator moves toward CLOSED,

immediately turn power OFF and proceed with the instructions that match your application. Permanent Split

Capacitor single-phase motors can be connected for opposite rotation by interchanging the leads T1 and T2

coming from the motor to the terminal strip.

Flow Control Division

Limitorque Actuation Systems

«
...
30
31
32
33
34
...
»

Summary of Contents for LY 1001 Series
































































Reviews:

No comments

Related manuals for LY 1001 Series

Brand: Fender Pages: 15

Brand: J D Squared Pages: 18

Brand: lancer Pages: 12

Precision2 HP2 Series

Brand: B-K lighting Pages: 6

Brand: Zero Hand Truck Pages: 38

Brand: B-K lighting Pages: 3

Brand: Garelick Pages: 2

Brand: Garelick Pages: 2

Brand: Hach Pages: 66

Brand: Hach Pages: 14

Brand: Hach Pages: 144

QuikChem 8500 2 Series

Brand: Hach Pages: 80

Brand: Hach Pages: 178

Brand: Hach Pages: 32

Brand: hager Pages: 4

Brand: Harken Pages: 4

Brand: Harken Pages: 2

TERRA FORCE BOOM

Brand: Hardi Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands