Limitorque LY 1001 Series Installation And Maintenance Manual Download Page 25

Page: 25 / 63

LMAIM1501

LY Installation and Maintenance for LY 1001, LY 2001 and LY 3001

5-11

5.8.2

Setting the CLOSED Mechanical Stop on the LY 2001/3001

Table 5.6 – Mechanical Stop and Locknut Screw Sizes

Unit Type

Stop Screw Size

Locking Nut Size

LY 2001/3001

⁵₈

-16 x 3”

⁵₈

-11

All piece numbers refer to Figure 5.11.

Set CLOSE Mechanical Stop Screws (piece #58) (Hex Head Cap Screw) by loosening Locking Nut (piece #59)

(Hex Head Nut).

Using the Handwheel, turn the valve to the CLOSE position. Make sure the valve is fully seated before setting

the mechanical stop.

Rotate Mechanical Stop Screw (piece #58) in the CW direction until contact with the Stop Pin (piece #28)

occurs.

Back-off Mechanical Stop Screw (CCW direction) approximately 1

¹₂

turns.

Retighten Locking Nut.

Manually operate the actuator through the close limit to assure setting is correct.

NOTE: The Mechanical Stops are intended to protect the equipment from overtravel if a Limit Switch fails. The

valve should not torque-out against the Mechanical Stop Screw during normal OPEN/CLOSE cycles.

Figure 5.11 – Mechanical Stop Set Screw Adjusted to Torque Drive Nut Contact Point on LY 2001 and 3001

#32 Torque Nut

#59 Locking Nut

#58 Mechanical Stop Screw

Mechanical Stop Screw

CLOSED OPEN

#28 Stop Pin and
Mechanical Stop
Screw positioned
at contact point

LY 2001/3001 Top View

CCW to Open

Flow Control Division

Limitorque Actuation Systems

Summary of Contents for LY 1001 Series
































































Search results

Summary of Contents for LY 1001 Series

Reviews:

Related manuals for LY 1001 Series

Brands by name

Popular brands

Limitorque LY 1001 Series, Installation And Maintenance Manual

Search results

Summary of Contents for LY 1001 Series

Reviews:

Related manuals for LY 1001 Series

Brands by name

Popular brands