Limitorque LY 1001 Series Installation And Maintenance Manual Download Page 16

Page: 16 / 63

5-2

LY Installation and Maintenance for LY 1001, LY 2001 and LY 3001

LMAIM1501

Table 5.1 – Torque Drive Nut Custom Bore and Keyway Sizes

Unit Type

Maximum Bore

Maximum Keyway

and Size

inch (mm)

LY 1001

¹₈

dia (28 dia)

¹₄

¹₈

(6 x 3)

LY 2001/3001

³₈

dia (60 dia)

⁵₈

⁵₁₆

(15 x 7.5)

NOTE: Before keywaying, match the Torque Nut with the Valve Stem to ensure proper keyway location. Use the

Keyway Index Mark (LY 1001 only) for locating appropriate keyway location.

Figure 5.2 – LY Keyway Locations

5.3

Installation Overview

CAUTION: Be sure to complete each step of the installation overview before electrically operating your

actuator. If the actuator is already mounted to a valve from the manufacturer, verify that the actuator is

mounted according to the following overview. Failure to follow the installation procedures could result in

personal injury and/or improper operation and could cause damage to the equipment.

Mount Torque Nut (piece #32) in the actuator as shown in Figure 5.3 with the following alignment:

For LY 1001 – Stop Lugs facing the Actuator Mounting Adapter with index lines positioned to face the

Mechanical Stop Screws.

For LY 2001/3001 – Torque Nut axially aligned on the Drive Sleeve so that the bottom of the nut is

positioned inside the Actuator Mounting Base.

LY 1001 Keyway
Location Marks

Torque Nut

Stop Lug

LY 2001/3001 Keyway
Location Positions

Flow Control Division

Limitorque Actuation Systems

Summary of Contents for LY 1001 Series
































































Search results

Summary of Contents for LY 1001 Series

Reviews:

Related manuals for LY 1001 Series

Brands by name

Popular brands

Limitorque LY 1001 Series, Installation And Maintenance Manual

Search results

Summary of Contents for LY 1001 Series

Reviews:

Related manuals for LY 1001 Series

Brands by name

Popular brands